Trailer Spindle Got a Nick In it from a Grinder Should the Axle be Replaced

Question

Question:

I was grinding the bolts off my trailer I slipped and put a nick in the spindle is it ok or do I need to replace it or the axle?

asked by: Dan

0

Expert Reply:

How deep is it? It is hard to tell from the picture. You may be able to use some emery cloth and take care of it unless it is too deep. Then you would want to go ahead and replace the axle. Even though spindles are available by themselves you would need special equipment and experience to weld on a new one so that it is straight. Replacing the axle is the safe bet.

I have included a link to the axles we carry to the right.

expert reply by: Michael H

0

click to enlarge

Answer 1

It could be a tow package fuse on the vehicle. Use the owners manual to find the locations of fuses/relays related to the tow package wiring to check them and replace as needed. If the issue is not a fuse or relay then you can test the vehicle side…

view full answer...

Answer 2

We do not carry any lug nuts with a rubber gasket and I personally would not recommend using any rubber gaskets for lug nuts. The hubs on your 2018 Jayco North Point will generate a lot of heat from the brakes. This would cause the rubber to become…

view full answer...

Answer 3

It sounds like you have a different size axle than anything we carry. The closest we have is the Dexter Trailer Axle w/ Electric Brakes - E-Z Lube - 6 on 5-1/2 Bolt Pattern - 86-1/2" - 5.2K #8327816-EB which has spring centers at 71-1/2 inches…

view full answer...

Answer 4

One of the big issues that EZ lube spindles create is that it's too easy to put too much grease into them which then either causes the seal to blow out or the cap to leak like what you have found. This oftentimes happens after that first trip…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Trailer Spindle Got a Nick In it from a Grinder Should the Axle be Replaced

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching