Troubleshooting Wiring for a Reverse Lockout Solenoid on an Old Boat Trailer
Updated 08/13/2014 | Published 08/12/2014 >
Question:
I have a tandem wheel boat trailer . Im trying to rewire this old 1988 trailer . The wheels have rotors and calipers . On the wiring to the solenoid is a black wire going in and on the back side a black wire coming out . My question is front wire needs to be attached to the blue wire to reverse lights ? .At the back of the solenoid is another black wire . Where does this wire go ? Trailer for ground ? thanks
asked by: Robert
Helpful Expert Reply:
Reverse lockout solenoids will have two wires as you have seen. One wire is grounded to the trailer and one wire is attached to a reverse light wire coming from the tow vehicle. On most lockout solenoids it does not matter which wire is grounded and which wire is connected to the reverse light wire.
Since I am not sure what solenoid you are using or how old it is, I recommend tracing both wires as far as you can. The ground wire should be attached to the frame somewhere on the trailer. It may also be ran to the main trailer ground.
Product Page this Question was Asked From
Replacement Solenoid Valve for Dexter Brake Actuators with Reverse Lockouts
- Accessories and Parts
- Brake Actuator
- Disc Brakes
- Hydraulic Drum Brakes
- Solenoid
- Valve
- Dexter
more information >
Continue Researching
- Search Results: for towing ~ 4 and 7~way wiring included trailer hitch
- Search Results: 7 way cord 7 way rv
- Search Results: brass brake line fittings
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Trailer Wiring
- Shop: TowSmart 7-Blade Trailer Connector w/ Jacketed Cable - Trailer End - 72" Long
- Shop: Mighty Cord 7-Way RV-Style Trailer Connector w/ Molded Cable - Trailer End - 6' Long
- Shop: Trailer Hitch
- Shop: Stealth Hitches Hidden Trailer Hitch Receiver w/ Towing Kit - Custom Fit - 2"
- Shop: ThinLine LED Tail Light for Trailers over 80" Wide - Stop, Turn, Tail - 11 Diodes - Red Lens
- Q&A: Self Tapping Screw Recommendation for Installing Exterior Light on Trailer
- Video: Comprehensive Review: Mighty Cord 7-Way RV-Style Trailer Connector w/ Molded Cable
- Video: All You Need to Know About the Mighty Cord 7-Way RV-Style Trailer Connector w/ Molded Cable
- Shop: Stealth Hitches Hidden Trailer Hitch Receiver w/ Towing Kit - Custom Fit - 2"
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Shop: TowSmart 7-Way RV Style Connector with Molded Cable - Trailer End - 6' Long - RV Standard
- Video: Review of TowSmart Trailer Wiring - 7 Blade Trailer Connector With Jacketed Cable - TS74RR
- Video: Review of Dexter Reverse Lockout Solenoid Tie Down Hydraulic Brake Actuator - DX46UR
- Video: Titan Brake Actuators with Reverse Lockout Replacement Solenoid Valve Installation
- Video: Titan Brake Actuator T4748800 Review
- Article: Wiring Trailer Lights with a 5-Way Plug (It's Easier Than You Think)
- Search Results: self tapping screws
- Search Results: thinline led
- Search Results: side marker trailer lights
- Search Results: 5 way wiring harness
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Article: Trailer Wiring Diagrams
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)

