Troubleshooting Code P0073 On 2026 Ford Maverick After Base Plate Installation
Updated 11/13/2026 | Published 11/08/2026 >
Question:
I just installed the Demco base plate in my 2026 Ford Maverick. Now I have a check engine lite with code P0073, which means there is a fault from my ambient temperature sensor, which looks intact. Any ideas before I have to take the front end off again?
asked by: Bob B
Expert Reply:
Hey Bob, sorry to hear that! Since the P0073 code appeared right after installing the Demco Base Plate # DM38CV, I'd start by checking the ambient temperature sensor's electrical connector and wiring. The sensor itself may look fine, but a loose connector, pinched wire, or damaged connection could trigger that code.
The sensor is located near the lower passenger-side grille, so you may be able to reach it without removing the entire front bumper. I'd check that the connector is fully seated and inspect the wiring around the base plate brackets for anything that may have gotten pinched during installation.
Where are you headed once you get your Maverick ready to flat tow?

William
11/12/2026
I also had the same fault and once I started the maverick up the code cleared. I Belive it was because I turned ignition on while sensor was disconnected.

Product Page this Question was Asked From
Demco Tabless Base Plate Kit - Removable Arms
- Tow Bar Base Plate
- Removable Draw Bars
- Twist Lock Attachment
- Completely Hidden
- Demco
more information >
Featured Help Information
Instructions
Continue Researching
- Video: Easily Install Your Demco Battery Charge Line Kit - 2026 Ford Maverick
- Video: Installation Guide Demco Tabless Base Plate - 2026 Ford Maverick
- Shop: Vehicle Tow Bar Wiring
- Shop: Roadmaster Tail Light Wiring for Towed Vehicles w/ 7-Wire to 6-Wire Straight Cord Kit
- Shop: Towed Vehicle Battery Charge Line Kit for Demco Air Force One and Stay-IN-Play Duo Braking Systems
- Shop: Roadmaster 7-Wire to 6-Wire Straight Cord Kit - 6-1/2' Long
- Article: Trailer Wiring Diagrams
- Search Results: trailer hitch
- Video: An In-Depth Look at the Roadmaster Battery Charge Line Kit for Towed Vehicles
- Shop: Trailer Hitch
- Q&A: Which is Better Roadmaster or Blue Ox Tow Bar
- Shop: Roadmaster 4-Diode Universal Wiring Kit for Towed Vehicles - 7-Way to 6-Way Coiled Adapter Cord
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: An In-Depth Look at the Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Shop: Trailer Wiring
- Q&A: Recommended Bike Rack and Dual Hitch Adapter for Carrying E-Bikes While Flat Towing
- Search Results: trailer wiring
- Q&A: How to Replace a Lance 6-Pin Plug w/ a Standard 7-Way Connector
- Shop: Blue Ox Patriot Portable Flat Tow Brake System - Proportional
- Video: Breaking Down the Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit
- Search Results: base plate for tow bar
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Suspension Enhancement
- Shop: Roadmaster Battery Charge Line Kit for Towed Vehicles
- Shop: Base Plate for Tow Bar
- Video: Comparing Portable Flat Tow Braking Systems - Curt RVi and Blue Ox Patriot
- Article: How to Measure for Trailer Hitch Drop
- Search Results: tow bar
- Q&A: Recommended Flat Tow Setup for a 2026 Ford Maverick



Rich
11/12/2026
Bob, did you attempt to turn on the vehicle while the sensor was disconnected? If so, this is what caused that code. I made the same mistake during my install. You can get any reader and download the code to clear it. Now that it’s connected and once it has been cleared, it will not come back and everything should be fine.