Replacement Brake Assemblies for a Dexter 5,200 lb Torflex Axle

Question

Question:

Will this brake assembly fit a Dexter 11 5200lb Torfex Torsion Axle?

asked by: Lauritz J

0

Expert Reply:

Hey Lauritz.

Assuming we are talking about the standard setup with the 5-bolt flange, then yes. The Dexter Electric Trailer Brake Assembly # 23-105 is a 12" x 2" manual adjust, driver side assembly. The passenger side is # 23-106, I recommend replacing both together. You could also pick up the kit # 23-105-106. Even though they say 6k axles, they are a confirmed fit with the 5,200lb axle you're working with.

Are you replacing the brakes because they’re worn out, or did you run into an issue with one side?

expert reply by: Trent G

0

Answer 1

Hey Brian, welcome back! Brake mounting hardware is not included with the etrailer Electric Trailer Brakes #AKEBRK-6. What you need is the Mounting Bolts and Hardware for 12" Brake Assemblies #BRKH12. This is enough for a pair of brakes, so you…

view full answer...

Answer 2

The best and easiest way to identify a replacement grease seal (or bearing for that matter) is by the original part's reference number. The linked photo shows the typical appearance and location of these part numbers on seal, bearings, races. It…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Replacement Brake Assemblies for a Dexter 5,200 lb Torflex Axle

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching