Hardware for etrailer Electric Trailer Brakes - 12" - Left/Right Hand Assemblies

Question

Question:

Hi..getting ready to order 2 sets AKEBRK-6 for Dexter axle 184357/57920, 5200 tandem 2016Keysto ne 325BH ....whats part for washer/bolts if separate..thanks

asked by: brian d

0

Expert Reply:

Hey Brian, welcome back! Brake mounting hardware is not included with the etrailer Electric Trailer Brakes # AKEBRK-6. What you need is the Mounting Bolts and Hardware for 12" Brake Assemblies # BRKH12. This is enough for a pair of brakes, so you will need a quantity of two if you're ordering two sets of brakes.

Also just a heads up, these are manual adjust brakes. If you want self-adjusting I recommend picking up the TruRyde Electric Trailer Brakes # TRU96FR instead.

Do you still have the 2016 Keystone Outback 325BH? Any big trips coming up once you get the brakes replaced?

expert reply by: Robin H

0

Mark W.

6/25/2026

Save your money reuse your boat that you take off you just have to remember to torque them to the recommended standards. That’s what I did.

Robin H.

6/25/2026

@MarkW that works if the hardware is in good shape, sure.

Mark W.

6/25/2026

@RobinH this is true rockin Robin

Answer 1

Hey Lauritz. Assuming we are talking about the standard setup with the 5-bolt flange, then yes. The Dexter Electric Trailer Brake Assembly #23-105 is a 12" x 2" manual adjust, driver side assembly. The passenger side is #23-106, I recommend…

view full answer...

Answer 2

The best and easiest way to identify a replacement grease seal (or bearing for that matter) is by the original part's reference number. The linked photo shows the typical appearance and location of these part numbers on seal, bearings, races. It…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 6

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 9

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Hardware for etrailer Electric Trailer Brakes - 12" - Left/Right Hand Assemblies

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching