Trailer Hitch for 2019 Jayco Seneca 37TS With 12,000 lb Capacity

Question

Question:

Looking for a Curt 12000lb trailer hitch for my 2019 Jay-co Seneca 37 ts .

asked by: dale d

0

Expert Reply:

Hey Dale! For a Curt hitch with that kind of rating you will need the Curt Class 5 Universal Weld-on Hitch w/ Brackets # C99CR. This fits frames up to 44" wide and has 18" brackets you can cut down to size for the best fit on your motorhome. It is a Class V hitch with a 2" receiver and a max gross trailer weight of 16,000 lbs. We do recommend taking this to a certified welder for installation.

What will you be towing with your Jayco?

expert reply by: Robin H

0

Curt Class 5 Universal Weld-on Hitch
(click to enlarge)

Dale D.

9/15/2026

Looking for a direct replacement . Not a hitch that will need labor welding and drilling new holes which will cost as much as the hitch.

Robin H.

9/16/2026

@DaleD I understand. Unfortunately, there are no aftermarket hitches designed as a direct-fit replacement for your Seneca. Jayco may have an OEM replacement available for the hitch that originally came on the motorhome, but the cost is likely higher than the Curt # C99CR even after factoring in the cost of having it welded in place. Either way, I would reach out to Jayco and see if a bolt-on replacement is available and go from there.

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 8

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 9

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 10

Hey Kelvin, welcome back. To flat tow a 2026 Ford Maverick with your Demco Commander II Tow Bar item #DM9511012, I recommend the following parts: Baseplate Kit - Demco Tabless Base Plate Kit item #DM38CV Wiring Harness - Roadmaster Diode 7-Wire to…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Trailer Hitch for 2019 Jayco Seneca 37TS With 12,000 lb Capacity

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching