Yakima OnRamp Replacement Knob for Y27TR Wheel Cradle

Question

Question:

Can one of these knobs- Replacement Wheel Tray Installation Knobs for Yakima OnRamp e-Bike Racks - Qty 4 Part Number: Y62AR be used to replace the missing grey knob on this cradle Y27TR? thanks!

asked by: CT G

0

Expert Reply:

Hi CT!

Yes, you’ve got the right one. I confirmed with Yakima that the Replacement Wheel Tray Installation Knobs for Yakima OnRamp cradle part # Y62AR, are the correct replacement knobs for the Y27TR wheel cradle. I’m sorry for the confusion earlier, especially when you’re just trying to make sure everything is secure before loading your bike.

What eBikes are you hauling on your OnRamp, and where do you like to ride most?

expert reply by: Heather A

0

Answer 1

Hi CT, Sadly, we don’t carry the gray knob by itself for your Yakima OnRamp XL. To replace that missing knob, you’ll need the complete Replacement Cradle and Strap for Yakima OnRamp Electric Bike Racks, part #Y27TR. I know replacing the whole cradle…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Yakima OnRamp Replacement Knob for Y27TR Wheel Cradle

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching