Bearing, Wheel and Tire, and Fender Recommendation for a 1991 Load Rite Lil Rider Trailer
Updated 07/23/2014 | Published 07/21/2014 >
Products Featured in This Question
Question:
I have a hub that is stamped with BT150A. It is a 1991 load rite lil riderinch trailer with 8inch tires. Do you know which bearing kit I can use. I cant find any numbers on the outer bearings or seal. Another question, I plan on taking this trailer on a 300 mile trip 600 round trip carrying about 300lbs. I plan to replace the bearings and tires/rims beforehand. I was going to use the old tire/rims and bearings as spares on the trip. The trailer needs fenders too. Will the 8inch wheels be ok on a long trip like that, should I go bigger-since I am buying wheels and fenders anyway - but Id have to buy a spare too.
asked by: Tim R
Expert Reply:
In order to determine which replacement bearings you would need to replace your current parts, you will need to either get the numbers that are stamped on your bearings, or you will need to get some precise measurements from your spindle.
The measurements you need will be where the seal and bearings ride. Check out the picture I attached to see which measurements are needed.
As long as your current trailer tires and rims have enough capacity for the weight that will be on your trailer you would be fine to replace them with the same sizes. If you have a 5.70-8 tire with a 4 on 4 inch bolt pattern you would want the Kenda Wheel and Tire part # AM30153.
5 on 4-1/2 inch bolt pattern part # AM30155.
If you have a 4.80/4.00-8 size tire you would want the # AM30000 if you have a 4 on 4 inch bolt pattern.
Part # AM30060 if you have a 5 on 4-1/2 inch bolt pattern.
I attached an FAQ on determining bolt patterns and a trailer size chart.
I also attached a link to a page that has all of the fenders we carry for 8 inch wheels.
Product Page this Question was Asked From
Grease Seals - Double Lip - I.D. 1.250" / O.D. 1.983" for 2,000-lb Axles - Qty 2
- Trailer Bearings Races Seals Caps
- Seals
- EZ Lube Seals
- Grease Seals - Double Lip
- 1.25 Inch I.D.
- 1.98 Inch O.D.
- 20000 lbs Axle
- TruRyde
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: cotter pin
- Search Results: l44643
- Search Results: bearing l44649
- Shop: Grease Seals - Double Lip - I.D. 1.250" / O.D. 1.983" for 2,000-lb Axles - Qty 2
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Search Results: trailer hitch
- Shop: Trailer Hitch
- Article: Trailer Wiring Diagrams
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Shop: Trailer Wheel Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Shop: Trailer Wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: trailer tires and wheels
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Search Results: trailer jack
- Q&A: Comparing Kenda KR03, KR35, And KR53 Tires
- Shop: Suspension Enhancement
- Video: Firestone Ride-Rite Air Bags with Easy Mount Compressor Feature Breakdown
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Q&A: What is a #84 Spindle and How Do I Know I Have One On My Trailer?
- Shop: Brake Controller
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Video: Hands-On with the Hub Saver Hub and Wheel Protector
- Search Results: trailer wiring
- Shop: etrailer Electric Trailer Brakes - Self-Adjusting - 12" - Left/Right Hand - 5.2K to 7K
- Article: How to Measure for Trailer Hitch Drop
- Video: Review of etrailer Trailer Hubs and Drums - Hub with Drum - AKHD-545-35-EZ-K
- Q&A: Instructions to Wire a Trailer for Electric Brakes
- Shop: Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles - 10" - 5 on 4-1/2 - Pre-Greased






