Kenda 4.80/4.00-8 Bias Trailer Tire with 8" White Wheel - 5 on 4-1/2 - Load Range C

Ask the Experts about this Kenda Trailer Tires and Wheels

• 18.5x8.5-8 Trailer Tire Replacement for Snowmobile Trailer
  We carry the tire size you need on a wheel with a 4 bolt pattern with the part # AM90002 but it's for a golf cart application. The most similar option that's for a trailer is the Kenda 165/65-8 part # AM3H200 which is mounted on a white 4 lug wheel like you are wanting. It will be about 2 inches shorter and narrower.
  view full answer...
• Replacement 4.80/4.00-8 Tire & Wheel Combination
  For your 4.80/4.00-8 tires and rims I recommend the Kenda 4.80/4.00-8 Bias Trailer Tire with 8" White Wheel - 5 on 4-1/2 - Load Range C # AM30060 or the galvanized wheel # AM30070. Each wheel will have a maximum load capacity of 745 lbs at 90 psi. This tire will have a diameter of 16.1 inches and a width of 4.7 inches. If you have the 4 on 4 inch bolt pattern, I recommend the powder coated # AM30040 or galvanized # AM30050.
  view full answer...
• Tire Pressure Recommendation for the Kenda 4.80/4.00-8 Bias Trailer Tire
  Trailer tires should always be inflated to their max psi to ensure you get the full weight capacity and the best tire wear. The Trailer Tire part # AM30060 that you referenced should be inflated to 90 psi when cold.
  view full answer...
• Can 18.5x8.5-8 Trailer Tires be Replaced with 4.80/4.00-8 Tires on a Snowmobile Trailer
  Kenda tire and wheel combo # AM30060 is a great option as long as the weight capacity is enough for the gross trailer weight. One of these tire and wheel combos is rated for 745 pounds at 90 psi. So for 2 of them on a single axle that would be a total capacity of 1,490 pounds. The center pilot hole is 2.8 inches in diameter and it has a 5 on 4-1/2 bolt pattern. If that is enough for the trailer then you will be good to go.
  view full answer...
• Speed Rating of the Kenda Tire and Wheel 4.80/4.00-8 on a 8 Inch Wheel
  Unless otherwise stated all specialty trailer tires are rated at 65 miles per hour. This is the max miles per hour this tire can sustain due to the excess heat build up that will occur if you go any faster. I would not recommend exceeding that speed for any length of time. I attached an FAQ article on trailer tires for you to check out also.
  view full answer...
• Will a 4.80/4.00-8 Trailer Tire Fit In Place of a 4.80-8 Tire
  The Kenda 4.80/4.00-8 Bias Trailer Tire with 8" White Wheel # AM30060 will fit in place for a 4.80-8 tire size. The wheel has a 5 on 4-1/2 bolt pattern so as long as that matches your existing bolt pattern it will work. If you just want the tire and want to keep your old wheels you can use # AM10004.
  view full answer...
• Offset and Backspacing for Rim and Tire Part # AM30060
  Trailer rims like the Kenda 4.80/4.00-8 Bias Trailer Tire with 8" White Wheel # AM30060 have a zero offset, meaning the mounting flange is dead center of the rim. Sounds like you are looking for the backspacing. Since this wheel has a zero offset all you need to do is take the width of the rim (3-3/4 inches), add 1 inch for both wheel lips (4-3/4 inches now), and then divide by 2. Which equals 2-3/8 inches. 2-3/8 inches is the figure you are looking for. Now would using a 2 inch spacer...
  view full answer...
• Can Trailer Hub/Drum # AKHD-545-2-EZ-2K be Used with 8 inch Wheel
  Yes the hub/drum part # AKHD-545-2-EZ-2K that you mentioned is compatible with 8 inch wheels like the Kenda wheel and tire # AM30060 that you also referenced.
  view full answer...
• Measurements of Kenda 4.80/4.00-8 Bias Trailer Tire with 8 White Wheel
  The Kenda 4.80/4.00-8 Bias Trailer Tire with 8" White Wheel - 5 on 4-1/2 - Load Range C # AM30060 will be approximately 6-1/2" from the lug nut hole to the ground. That will have little bearing on the tire clearance, however. The most important things to know are that it is overall 16.1" in diameter and is 4.7" wide. These numbers will be the determining factor on if you have enough clearance for the tire to fit without interfering with your fender or sidewall. I've added a link to...
  view full answer...
• Will the Valve Stem That Comes with Kenda 4.80/4.00-8 Trailer Tire W/ White Wheel Hold 90 Psi
  The valve stem that comes with the Kenda 4.80/4.00-8 Bias Trailer Tire with 8" White Wheel part # AM30060 is rated for the max psi range of the tire which is 90 psi therefore you won't have any issues. If you feel more conformable with a higher rated valve stem we do offer the Americana Metal, Bolt-In Valve Stem part # AM20906 which is rated for over 100 psi.
  view full answer...
• Shorter Wheel Tire Recommendation to Fit Trailer Inside Barn Door
  The part # AM30060 does have the correct bolt pattern to allow it to bolt up to your trailer hub. As long as your trailer does not have brake assemblies these rims would fit over the hubs and work well from a fit point of view. The weight capacity of this wheel/tire setup is 745 lbs though which wouldn't be enough for your 2,500 lb trailer. Your best option would be the part # AM31215 that will be 6 inches shorter than what you currently have. This has the right bolt pattern, enough...
  view full answer...
• What is Pilot Diameter of Kenda 4.80/4.00-8 Bias Trailer Tire with 8" White Wheel
  The pilot diameter for the wheel part # AM30060 that you referenced is 2.80 inches or 2-51/64 of an inch if you are being super accurate. This is pretty close to 2-7/8 inches which in decimal form is 2.875 inches.
  view full answer...
• I Want a Larger Tire for my Coleman Pop Up Camper That has Tire Size 4.80/4.00-8
  We have what you're looking for. Depending on the amount of room that you have is going to determine the size you can go up to. The original tire that you have like the Kenda 4.80/4.00-8 Bias Trailer Tire part # AM30060 is about 16.1" Tall and 4.6" wide. The first notable step up would be a Kenda 215/60-8 Bias Trailer Tire part # AM3H325 which is about 18.3" Tall and 8.9" Wide. This one is significantly wider than you current tire but just slightly taller. For a good increase in...
  view full answer...
• Recommended Replacement Tire and Wheel Combo for Tire Size 4.80/4.00-8
  If you are looking for a replacement tire and wheel combo with the tire being a size 4.80/4.00-8 then we do have some possible solutions for you. If your current wheel uses a 4 on 4 bolt pattern then I recommend going with the Kenda 4.80/4.00-8 Bias Trailer Tire with 8" White Wheel # AM30040. This has a Load Range C which means that the max load for it is 745 lbs at 90 psi. If, however, your current wheel uses the 5 on 4-1/2 bolt pattern you will want to go with the Kenda 4.80/4.00-8...
  view full answer...
• Recommended Replacement Tire & Wheel for Motorcycle Trailer
  Unless otherwise noted all trailer tires are only rated for up to 65 miles per hour. Going faster than that causes heat to build up which then causes the tires to fail. For a white wheel and tire that would work as a replacement and would match your current size you would want the part # AM30060. This setup would have a maximum capacity of 760 lbs per tire at 90 psi. With trailer tires you want to have them inflated to their max PSI at all times. Any less pressure will cause the capacity...
  view full answer...
• 4.80/4.00-8 Tire Compatibility with Speeds up to 70 MPH on Drag Mini Bike
  We do not have a 4.80/4.00-8 tire that is rated for that speed. These tires are however rated for loads of up to 590 or 745 lbs at the max psi listed on the tire and are rated based on long distance driving under that load for 65 mph at their max psi so they don't overheat and fail. I can't confirm that the Kenda K371 Bias Trailer Tire - 4.80/4.00-8 - Load Range C # AM10004 or any other trailer tire will work on your drag mini bike as they haven't been tested for that use or the speeds...
  view full answer...
• What is the Highest Rated 4.80-8 Trailer Tire or Tire and Wheel Combo Available
  For a 4.8-8 trailer tire with the most weight carrying capacity, we have # AM10004. This is a tire by itself and it is rated for 760 pounds at 90 psi. It fits 8 x 3-3/4 inch wheels. The highest rated tire and wheel combo in this size with a 4 on 4 bolt pattern is # AM30040, also at 760 pounds at 90 psi. The highest rated tire and wheel combo with a 5 on 4-1/2 bolt pattern is # AM30060 at 760 at 90 psi also. I have included a link to our tire and wheel FAQ articles for you.
  view full answer...
• Bearing, Wheel and Tire, and Fender Recommendation for a 1991 Load Rite Lil Rider Trailer
  In order to determine which replacement bearings you would need to replace your current parts, you will need to either get the numbers that are stamped on your bearings, or you will need to get some precise measurements from your spindle. The measurements you need will be where the seal and bearings ride. Check out the picture I attached to see which measurements are needed. As long as your current trailer tires and rims have enough capacity for the weight that will be on your trailer...
  view full answer...
• Replacement Log Splitter Tire Size 4.80/4.00-8
  We have what you are looking for. It is the Kenda K371 Bias Trailer Tire - 4.80/4.00-8 - Load Range C # AM10004. It is rated for 745 lbs at 90 psi. It has an outer diameter of 16.1 inches and a width of 4.7 inches when inflated to 90 psi. If you want the wheel along with the tire, we have the 4 on 4 inch bolt pattern # AM30040 or the 5 on 4-1/2 inch bolt pattern # AM30060. These tires are rated for a max speed of 65 mph.
  view full answer...
• Recommended Tire and Wheel Combination for Log Splitter
  For your log splitter wheel and tire combination, the pilot hole in the center will be much larger than the hub center. This is not an issue as the wheel will bolt to the hub and be centered based on the lug studs and lug nuts. All trailer spindles will have the single nut holding that wheel bearing in place as you stated. If you have no lugs and only the single center nut then I don't have any wheel options available for that hub centered assembly. My recommendation is the Kenda 4.80/4.00-8...
  view full answer...
• Can a Load Range C Tire be Used Instead of a Load Range B Tire on a Trailer
  First, make sure that you stay within the gross trailer weight capacity for your trailer. If that 200 pounds extra puts you over the gross trailer weight capacity then you will want to carry that extra weight in the vehicle. Going with a higher capacity tire will not increase the gross trailer weight capacity. With that said since you have a long way to go and such small tires, having a stronger tire in the same size would help to reduce the chance of anything happening to the tires....
  view full answer...
• Reducing Height With Tire Smaller Than 145-12 for Pontoon Trailer
  The difference in diameter between an ST145R12 tire like the Kenda Karrier S-Trail # AM31202 and the Loadstar 4.80-12 # AM30670 is about 1". The 145R12 has an overall diameter of 21.3" while the 4.80-12 has an overall diameter of 20.5". Please note that if you were to make this conversion you would be lowering your weight capacity by 230 lbs per tire/wheel. If you are looking to go with the smallest tire/wheel available then you are looking at the Kenda 4.80/4.00-8 # AM30060. The problem...
  view full answer...
• Wider Tire to Replace 4.80 x 8 Load Range C Tires
  The 4.8 x 8 tires like # AM30060 are 4.7 inches wide and use a 3-3/4 inch wide wheel. For a wider tire I recommend the Kenda K353 Bias Trailer Tire - 5.70-8 - Load Range C # AM10012. This tire is 5.9 inches wide. This tire will be 18 inches diameter when inflated and is rated for 910 lbs at 75 psi. This tire will not only be wider but will almost be 2 inches taller raising your trailer by about 1 inch. For any other tire, you would also need to replace the wheel.
  view full answer...
• 8 inch Wheel and Tire with a Larger Pilot Diameter than 2.5 Recommendation
  Is it possible that you have a 2.8 inch pilot diameter? If so we have some options that would work like the part # AM30060 that has a 5 on 4-1/2 inch bolt pattern and a 2.8 inch pilot diameter. If you have a 4 on 4 inch bolt pattern you would want the part # AM30050. If you are unsure of your wheel's bolt pattern I attached an FAQ article that will help you determine your bolt pattern.
  view full answer...
• Timbren Axle-Less System Recommendation for a Small Utility Trailer
  What we offer that would work well for your utility trailer is a Timbren Axle-Less system like the # A20RS545 that comes with hubs that are 5 on 4-1/2 inch. For a wheel and tire combo that would match the trailer tire size you have and the bolt pattern of the Timbren you would want the # AM30060. If you wanted a traditional style axle you would have to contact a local trailer shop that can order you in custom axles as we do not have ones that would fit it. The Timbren would be the...
  view full answer...

Do you have a question about this Trailer Tires and Wheel?