Recommended 7-Way Connector and Brake Controller for a 2009 VW Touareg TDI

Question

Question:

Re 2009 VW TouaregTDI v6 3.0. Hoping you can assist with a shopping list for my vehicle. This vehicle does not have a factory tow package. It has an aftermarket class 3 hitch. I had the 4 pin plug replaced with a 7 pin - but the installation was not totally correct as either the brake lights or indicators were not working- i have not towed for several years . I am looking to purchase a travel trailer and want to endure everything is setup correctly. So can you recommend all the correct wiring harnesses etc and a brake controller for this vehicle . Will appreciate your assistance. Thanks

asked by: Gary T

0

Expert Reply:

I sure Gary, and thanks for the information! To add a 7-Way wiring harness and brake controller to your 2009 VW Touareg TDI, I recommend the following parts:

4-Way Wiring Harness - Curt Powered Tail Light Converter item # C59236

7-Way Wiring Harness - Universal Installation Kit for Trailer Brake Controller item # ETBC7.

Brake Controller w/ Universal Harness - Redarc Tow-Pro Liberty item # RED52VR

I attached a couple of wiring diagrams below so you can see how to get the 7-Way and brake controller installed. The 4-Way connector will need to be spliced directly into the factory wiring harness going to the tail lights on your VW.

What kind of travel trailer are you looking at getting?

You can add this information, along with any other questions you have, where it says Add Comment.

expert reply by: Jerred H

0

RED52VR
(click to enlarge)

ETBC7
(click to enlarge)

Tim F.

7/14/2026

I installed the Redarc Tow-Pro Liberty item # RED52VR on a 2023 Chevy Colorado. Installation was straight forward and the controller is great to work with. It is very accurate on the control of break pressure. By past experience, I have learned that one of the most important connections is the ground! Tim F

Jerred H.

7/14/2026

@TimF That's a great tip Tim and you are 100% correct. Thanks for taking the time to share that feedback!

Answer 1

Hey Kaleb I have all the parts you will need to add a 7-Way connector and a brake controller to your 2002 Toyota Tundra but only one of them is going to be plug and play. Everything else will have to be wired in. There is no brake controller adapter…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 11

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Recommended 7-Way Connector and Brake Controller for a 2009 VW Touareg TDI

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching