Replacement Idler Hub For ShoreLand'r Trailer

Question

Question:

Help finding idler hub for a Shorelander trailer. See image

asked by: Marc W

0

ShoreLand'r Trailer Info
(click to enlarge)

Expert Reply:

Hi Marc! That particulr ShoreLand'r trailer typically has 3,500 lb axles. However, you will need to confirm this information. I recommend taking a look at your axle tags, it is typically listed on the tag.

Assuming that is correct, you can use the Kodiak Trailer Hub for 3,500-lb Axles - 5 on 4-1/2 - Stainless Steel # KH84545S you were looking at. This doesn't include bearings so you would also need the Hub Bearing Kit # BK2-100. If this is a spare and you want a pre-greased option you could also use the galvanized # CE13515.

What kind of boat do you haul?

expert reply by: Robin H

0

Kodiak Trailer Hub
(click to enlarge)

Marc W.

7/2/2026

Thank you for this information. Can you also tell me the part #'s for the leaf springs and related components?

Robin H.

7/3/2026

@MarcW you will have to measure the leaf springs for me to find the right replacement, again assuming 3,500 lb axles here. See the articles below. If you want shackle straps and equalizers (assuming tandem axle) those also have to be measured.

Helpful Links

faq-double-eye-trailer-suspension-review.aspx

faq-how-to-accurately-measure-trailer-leaf-springs.aspx

Answer 1

In order to find the correct replacement hubs for your Shoreland'r boat trailer, you need to first know what bearings your current hub has. You will need to take apart your current hub assembly and look at the bearings themselves; wipe away the…

view full answer...

Answer 2

Hi Don; I wasn't able to find anything with the model number and even if I could, I would only be guessing at the axle size for a replacement hub. You will need to identify your axle to find the right hub. You can either look for an axle tag or…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 5

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 8

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 9

The Dexter Nev-R-Adjust electric trailer brakes can be manually adjusted. There are a couple teeth of the adjustment wheel that are exposed just under the lever that you referenced. I have attached a photo showing the teeth. You will likely need a…

view full answer...

Answer 10

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 11

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 12

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Replacement Idler Hub For ShoreLand'r Trailer

Products Featured in This Question

Continue Researching