bing tracking image
Q & A Icon

MORryde X-Factor Crossmember for a 2019 Cruiser RV Stryker ST-3116  

Updated 07/01/2026 | Published 06/23/2026

Question:

2019 cruiser rv stryker st- 3116. Looking to add a set of crossmembers preferably front and rear brackets. The brackets are single hole, welded U shape with 39456 stamped on them. Holding leaf springs. Pics are available.

0

Expert Reply:

Tony, I'd be happy to help with that.

I wasn't able to identify the hanger based on the "39456" stamping, but I was able to confirm that your 2019 Cruiser RV Stryker ST-3116 commonly came from the factory with Dexter E-Z Flex suspension. That's good news because the MORryde X-Factor crossmembers part # MR33WR are designed to work with standard leaf spring hangers like those used with the Dexter E-Z Flex system and are an excellent way to strengthen the suspension and reduce stress on the hangers.

Where do you take your Stryker most often, boondocking with your toys or mostly highway trips?

expert reply by:
0
Heather A
cross
cross
(click to enlarge)
Tony profile picture

Tony

6/26/2026

I carry a Polaris xp4 1000 and although mostly highway, there are several opportunities that I will be offroad.

Heather A. profile picture
Etrailer Expert

Heather A.

6/27/2026

@Tony Nice! The Crossmember will help with those off road situations for sure. I will be able to identify if you have the Dexter EZ flex system if you send me a photo of your suspension especially the hangers to [email protected]
Tony profile picture

Tony

6/27/2026

@HeatherA Sent
Heather A. profile picture
Etrailer Expert

Heather A.

6/30/2026

@Tony I did get your photos and you do have the Dexter Ez Flex suspension so the MORryde X-Factor crossmembers part # MR33WR are what you need.
See All (5) Replies to Tony ∨
Jeff M. profile picture

Jeff M.

6/27/2026

Tony, I have a 2017 Shadow Cruiser 225rbs. I've had to replace 3 axles on it. I guess I can take credit for the 1st one but the last two have to be chalked up to roads. Although you'd think you'd notice. I replaced the standard hangers along the way which then had to be drilled to accommodate the crossmembers. But the center hangers remained the same and the crossmembers bolted up with no problem. I have a CRE3000 as well. I think I can tell the suspension is a little stiffer from side to side while towing. It seems to feel a better in longer left turns. It's hard to tell though. So, knowing the additional bracing is there helps me feel that I've done just about everything to improve the suspension w/o going overboard. It is a ten year old trailer. Gotta get another 5 - 10 out of it! Hope this helps. Oh, you mentioned off road. IDK about that, dirt roads that are in fair shape (not too groovy), I'd say okay.

Larry profile picture

Larry

6/28/2026

Easy install on Montana 3121 on center and rear hangers. Haven't installed on front hangers due to drain pipe interference. Offset brackets are available but haven't added yet. Suspension seems tighter.

Tony profile picture

Tony

6/28/2026

@Larry Thanks Larry
Heather A. profile picture
Etrailer Expert

Heather A.

6/30/2026

@Larry Great to know Larry! Can I ask what type of issues you were having before adding the Crossmembers?
Larry profile picture

Larry

6/30/2026

Some wearing on outside of tires, but think that was mostly due to scrubbing, I have to make almost a 90 degree turn backing in my driveway. Mostly for peace of mind. Have ready several stories of spring hangers breaking.
See All (4) Replies to Larry ∨

Product Page this Question was Asked From


Q & A Icon

Continue Researching

See More Q&A Expert Answers >>