Instructions For Installing Replacement Fender Assembly for Demco Kar Kaddy SS Tow Dolly DR74FR
Updated 06/22/2026 | Published 06/16/2026
Question:
We recently ordered the DR74FR which we did receive, but it did not come with the instructions. Can you send those to us please to this email address? Thanks!
asked by: Melissa L
Expert Reply:
Hey Melissa, thanks for reaching out. It doesn't look like Demco provides an online version of the instruction sheet for replacing the # DR74FR fender, but I can give you some general instructions.
First, you'll want to remove the damaged fender assembly by taking out the mounting hardware securing it to the wheel pan/frame. Next disconnect the light wiring from the old fender while taking note of the wire routing.
Then position the new fender assembly in place and loosely install the mounting bolts. Next reconnect the wiring and route it the same way as the factory wiring. Make sure it is secured away from any moving parts. Then just tighten all the hardware, and make sure the fender is aligned over the tire. Test the lights before towing and you'll be good to go. Hope this helps!
(click to enlarge)
Product Page this Question was Asked From
Replacement Fender Assembly for Demco Kar Kaddy SS Tow Dolly - Passenger Side
- Accessories and Parts
- Trailers
- Tow Dolly Parts
- Fenders
- Demco
more information >
Continue Researching
- Shop: Replacement Right Side Ratchet Winch - Demco Kar Kaddy 3, Kar Kaddy SS, and Kar Kaddy X Tow Dollies
- Shop: Winch Ratchet Repair Kit by Dutton-Lainson
- Search Results: kar kaddy
- Shop: Replacement Water Module Assembly for Thetford Aqua-Magic V and Aqua-Magic VI RV Toilets
- Shop: Trailer Hitch
- Article: Trailer Wiring Diagrams
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Search Results: trailer hitch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Search Results: trailer wiring
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Shop: Trailer Wiring
- Shop: Suspension Enhancement
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: etrailer Anti-Rattle Hitch Collar for 2" Hitch Receivers
- Search Results: trailer tires and wheels
- Q&A: Does etrailer Carry Furrion Chill Cube w/ Heat Pump to Replace Dometic Duo-Therm
- Search Results: trailer jack
- Article: How to Measure for Trailer Hitch Drop
- Shop: Power Mountain Tallboy Off-Road Bottle Jack - 8-1/2" to 37-3/4" Lift - 6 Tons
- Shop: Brake Controller
- Q&A: Recommended Bike Rack and Dual Hitch Adapter for Carrying E-Bikes While Flat Towing
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Shop: Base Plate for Tow Bar
- Shop: Redarc Tow-Pro Liberty Brake Controller w/ Universal Wiring Harness - Dash Knob - Proportional
- Video: Clean Up Your Trailer Wiring
- Search Results: trailer hitch ball mount
- Q&A: Instructions to Wire a Trailer for Electric Brakes
on Accessories and Parts
Randy
6/19/2026
You will want to remove the tire if you want easy access. I will look when I get home. I may have the instructions. An item that is not in the instructions for the light. Insert the rubber in the opening, plug in the light then push into the opening. It will be tight but it does fit. Make sure it is in all the way securely. If you don't do it correctly you will loose the rubber some where on the highway.