Fit Kit For Thule Evo On 2025 Honda CR-V

Question

Question:

We have a Thule Hullavator system on an EVO roof rack that has been on several vehicles. The last one was a 2014 Subaru Outback. We now have a 2025 Honda CRV and I need the right mounts to fit it. I know they are fixed mounts, but I cannot tell which are the right ones for me to use. Can you help?

asked by: Daniel D

0

Expert Reply:

Hi Daniel; if you have the flush rails on your 2025 Honda CR-V you need the Fit Kit for Thule Evo Flush Rail and Edge Flush Rail Roof Rack Feet # TH52KE. If you don't have any rails, you need the Fit Kit for Thule Evo Clamp and Edge Clamp Roof Rack Feet # TH52BE which clamps on.

What kind of kayaks are you carrying?

expert reply by: Robin H

0

Evo Fit Kit 6159
(click to enlarge)

Daniel D.

6/19/2026

We have several, but primarily 12’ touring kayaks.

Robin H.

6/19/2026

@DanielD sounds like you get a lot of use out of your rack and Hullavator. If you need anything else don't hesitate to reach out!

Daniel D.

6/19/2026

@RobinH, Yes we do. Had them for a long time. I think I also need replacement foot assembly as well though, what I have on my EVO bar right now is meant for a crossbar. I can send picks if you have a way to receive them

Robin H.

6/19/2026

@DanielD sure you can send me pictures by email. If you respond to any of those emails with links for this page they will come directly to me. Do you have the flush rails or a naked roof on your CR-V?

See All (4) Replies to Daniel D. ∨

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 8

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Fit Kit For Thule Evo On 2025 Honda CR-V

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching