Recommended Lock for a 2-5/16" Dexter/UFP CD-200 Coupler

Question

Question:

I need a trailer hitch lock for a Dexter C200 2-5/16 ball. You show a unit for A-60 Dexter. Will it work on the C200? Or what do you suggest?

asked by: Bryce J

0

Expert Reply:

Unfortunately, it will not Bryce but I do have one that will. For the Dexter/UFP CD-200 Coupler item # DX33CR, you'll need the InfiniteRule Trailer Coupler Lock item # IR63FR. This lock is going to surround your 2-5/16" coupler and secure below with keyed unique hitch pin. The bracket expands to fit up to 4-1/2" wide couplers so it'll work great with the CD-200 Coupler item # DX33CR.

The InfiniteRule Trailer Latch Lock for Dexter A-60 Trailer Coupler item # IR82FR you were looking at isn't going to be wide enough to get through both sides of the item # DX33CR. It's designed specifically for a 2" coupler so the inside span is only 3-1/8".

I remember working with you last year. Is this for your Century Coronado boat's trailer? Where do you store your boat when you're not using it?

You can add this information, along with any other questions you have, where it says Add Comment.

expert reply by: Jerred H

0

IR63FR
(click to enlarge)

Bryce J.

6/11/2026

Thanks Jerred Yes for the new trailer for the 1961 Coronado. Got the Curt Echo a few weeks ago but haven't tried it out yet. We built new house and have two 30 x 30 garages on either side so plenty of garage space to house the Coronado.

Jerred H.

6/11/2026

@BryceJ You're welcome! That sounds like an amazing setup, congratulations! I got goosebumps thinking about it. You're going to like that Curt Echo. Make sure you don't submerge it though when you're putting your Coronado in or out. It's weatherproof but not submersible.

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 5

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 8

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Answer 11

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 12

Hey Lucas! I measured the Buyers Products Weld-On Receiver Tube #337RT25824B in our warehouse using my digital caliper, and it has an exact outer diameter of 2.54", so I don't believe it will work with your truck's 2-1/2" receiver.…

view full answer...

Recommended Lock for a 2-5/16" Dexter/UFP CD-200 Coupler

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching