Would the Brophy Camper Scissor Step Work with my Tailgate?
Updated 06/13/2026 | Published 06/08/2026
Products Featured in This Question
Question:
I have truck camper with tailgate down. Would this work? Or do you have a better suggestion? Thank you! Ryan Brophy Camper Scissor Steps - 3 Steps - Aluminum - Non-Slip Tread - 24 Wide - 300 lbs Part Number: AS23
asked by: Ryan C
Expert Reply:
Appreciate you reaching out Ryan,
The best way to determine if the Brophy Tailgate Scissor Step # AS23 will work with your F150 is to measure from the top of the tailgate down to the ground. That measurement will help determine whether the steps are the correct height.
To secure the Brophy Scissor steps you'll need to check the available mounting space on your tailgate. The Brophy Tailgate Scissor Step Mounting Bracket # TSSB measures about 18 1/8" wide and the mounting pins are spaced 15" apart center to center, so you'll need enough room to drill those mounting holes and install the bracket securely.
Do you currently have any steps on the camper or are you starting from scratch for your setup?
(click to enlarge)
Lisa
6/12/2026
We use the steps on our hay wagon, and they work great. Matter a fact we are getting ready for a 4th of July parade. They fold up quickly and are sturdy, but not overly heavy. Make sure you measure correctly. Would have been nice if they supplied a way to attach a photo in this post. Very happy with this purchase.
Phil S.
6/13/2026
Sorry Ryan I can't help you on this. I have a Lance truck camper and the tailgate is removed. I measured from the entry to the ground and the 3 steps work fine. I just use a couple of 2x6 lumber on the bottom support to level up the steps on higher ground. Phil
Product Page this Question was Asked From
Brophy Camper Scissor Steps - 3 Steps - Aluminum - Non-Slip Tread - 24" Wide - 300 lbs
- RV Steps
- Truck Camper
- Snap-On Step
- 24 Inch Wide Step
- 24 Inch Wide
- 3 Steps
- 8 Inch Drop/Rise
- 24 Inch Entry
- 25 Inch Entry
- 26 Inch Entry
- 27 Inch Entry
- 28 Inch Entry
- 29 Inch Entry
- 30 Inch Entry
- Aluminum
- Brophy
more information >
Continue Researching
- Shop: Brophy Camper Scissor Steps - 4 Steps - Aluminum - Non-Slip Tread - 24" Wide - 300 lbs
- Video: TorkLift Scissor Steps SafeStep Vinyl Barrier Review
- Q&A: Recommended Scissor Step For A 36" Entry Height
- Shop: Brophy Camper Scissor Steps - 3 Steps - Aluminum - Non-Slip Tread - 24" Wide - 300 lbs
- Shop: Safety Step Sand Away Dirt Trapping Step Cover - 22" Long x 11-1/8" Wide
- Shop: Prest-O-Fit Outrigger Exterior RV Step Rug - Curved - 22" Wide - Blue - Qty 1
- Shop: TorkLift SmartStep GlowStep Revolution Uprising - 5 Step - 30" Wide - RV Entry Steps
- Shop: Brophy Tailgate Scissor Step Mounting Bracket
- Shop: Lippert SolidStep 4.0 RV Steps for 26" Wide Doorways - 3 Steps
- Shop: Vehicle Tow Bar Wiring
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Trailer Wiring Diagrams
- Shop: Trailer Hitch
- Search Results: trailer hitch
- Video: An In-Depth Look at the Roadmaster Battery Charge Line Kit for Towed Vehicles
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Shop: Trailer Wiring
- Search Results: trailer wiring
- Shop: Suspension Enhancement
- Q&A: Does etrailer Carry Furrion Chill Cube w/ Heat Pump to Replace Dometic Duo-Therm
- Search Results: trailer tires and wheels
- Article: How to Measure for Trailer Hitch Drop
- Video: An In-Depth Look at the Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit
- Search Results: trailer jack
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Base Plate for Tow Bar
- Shop: Brake Controller
- Q&A: Best Suspension Upgrade for 33" Tandem Axles: Road Armor vs Dexter EZ Flex for Ember 22ETS
on RV Steps
Martin V.
6/10/2026
The quality of the steps is excellent. I knew that I would have to modify the step for my proposed use. I use the 3 step on a 2004 Itasca class-C entrance. I could not use the 3 step height on the entrance and the 2 step was too short. By removing the upper hardware and reinstalling the attach hardware on the back of the step, the height was perfect for my class-C motor home. Carefully drilling out the rivets and then using 1/4-20 bolts with washers and self-locking nuts to assemble (without the upper two vertical long pieces and the 2 horizontal pieces) and then attached the mounting assembly to the back of the top step. I have used this now for over a year without any issues.