Is There a Replacement for the Tie Down LP80 Brake Actuator?
Updated 06/09/2026 | Published 06/02/2026
Products Featured in This Question
Question:
Im using a tie-down actuator LP80, but are there any actuators that can be installed on it without any modifications?
asked by: syo w
Expert Reply:
Hi Syo,
There is not an exact replacement that will slide into place to replace your Tie Down LP80 because it has been discontinued, so you would have to go with a completely new actuator. It looks like the Tie Down LP fits a 3" wide channel tongue, if that's the case for your trailer, you can use something like the Dexter DX7.5L A-60 Brake Actuator w/Electric Lockout part # DX89FR. It bolts-on to 3" wide trailer tongues and its mounting holes are spaced 3" apart center to center so you made need to drill holes into your frame to install it.
The electric reverse lock out will allow you to back up without activating your trailer's brakes using the reverse signal from your tow vehicle toa solenoid inside the actuator. The over-center latch mechanism automatically engages when fully seated on a 2" hitch ball to provide you with a safe, secure connection to your trailer while towing.
What kind of trailer are you replacing the actuator on?
Product Page this Question was Asked From
Dexter DX7.5L A-60 Brake Actuator w Electric Lockout - Bolt On - Disc - 2" Ball - Zinc - 7.5K
- Brake Actuator
- Surge Brake Actuator
- Boat Trailer
- Construction Trailer
- Farm Trailer
- Travel Trailer
- Utility Trailer
- Bolt-On
- 7500 lbs GTW
- 2 Inch Ball Coupler
- 3 Inch Channel Tongue
- Disc Brakes
- Electric Lockout
- Manual Lockout
- Dexter
more information >
Continue Researching
- Shop: Demco Hydraulic Brake Actuator w/ Electric Lockout - Disc - Zinc - 2" Ball - 7,000 lbs
- Article: Parts Needed to Add Hydraulic Disc Brakes to a Trailer
- Q&A: Replacement Surge Brake Actuator For Venture Commander 6000 Boat Trailer To Fit Multiple Ball Sizes
- Shop: Trailer Hitch
- Shop: Kodiak Disc Brake Kit - 10" Rotor - 5 on 4-1/2 - Dacromet and Stainless Steel - 3,500 lbs
- Shop: Dexter DX7.5L A-60 Brake Actuator w Electric Lockout - Bolt On - Disc - 2" Ball - Zinc - 7.5K
- Shop: Kodiak Hydraulic Brake Line Kit - Single Axle - 18'
- Shop: Hydrastar Hydraulic Brake Line Kit - Single Axle - 25' Long, 3/16" Main Line
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Dexter Zinc-Plated Brake Actuator w/ Electric Lockout - Disc - Multi-Fit Ball - Bolt On - 7,000 lbs
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Search Results: trailer hitch
- Article: Trailer Wiring Diagrams
- Video: How to Choose a Trailer Brake Controller
- Search Results: trailer wiring
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Shop: Trailer Wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Article: How to Measure for Trailer Hitch Drop
- Search Results: trailer tires and wheels
- Shop: Suspension Enhancement
- Video: What to Know About the Curt TriFlex NEXT Trailer Brake Controller
- Q&A: Installation Time for Blue Ox BX1128 Flat Tow Base Plate Kit for 2016 Jeep Grand Cherokee
- Article: How to Choose the Right Trailer Hitch Class
- Search Results: trailer jack
- Shop: Brake Controller
- Shop: Base Plate for Tow Bar
- Q&A: Recommended Bike Rack and Dual Hitch Adapter for Carrying E-Bikes While Flat Towing
on Brake Actuator
Syo W.
6/8/2026
Thank you for your reply. Based on the photos I attached of my Ranger trailer, do you believe the Dexter DX89FR would require only one additional mounting hole? Or are there any other modifications that you can see from my photos?