Availability of Replacement Capsules for Wesbar Trailer Lights

Question

Question:

I have a 2003 Four Winns Trailer light out on the right side and need a replacement capsule WESBAR 107963 but dont see a replacement. Four Winns Part LIGHT, RT TAIL #109308 USE 005-1351 Thanks,

asked by: Kevin

0

Expert Reply:

Some Wesbar lights have a the sealed type of capsule, and they are not meant to be opened. Instead, you would need to replace the whole capsule. The good news is that Wesbar offers replacements, depending on the model number, that can be easily opened to change worn parts, in addition to the sealed type.

If you have a Wesbar Submersible Low Profile Light # 403026 and/or # 403076, the bulbs can be replaced by removing the clear capsule inside the light.

If you want to swap it out for the kind with which you can replace the bulbs yourself, use # 403356. The 403356 capsule uses bulbs # A1157B, and/or # 194 (# A194B).

expert reply by: Jameson C

0

Roger

7/16/2024

I have a 2003 Fourt Winns boat and trailer that I need the right tal light assembly for. Any ideas?

Jameson C.

7/16/2024

@Roger The great thing about trailer taillights is that if you can find a replacement that looks like what you have it will work since they all are made to a few designs. I attached a link to all of the trailer taillights we carry but you can also email me back with a picture of what you have and I'll see what you'd need and if we can help.

Helpful Links

dept-pg-trailer_lights-sf-tail_lights.aspx

Answer 1

Since you said you want to re-wire your entire trailer I recommend the Optronics Submersible Trailer Light Kit, part #TL5RK. This kit comes with 2 stud-mount lights, 2 amber side marker and clearance lights, a license plate bracket, and a 25 ft…

view full answer...

Answer 2

Typically 4-way wiring consists of 18 and 16 gauge wires. For a 4-way that has all 16 gauge wire you would want the Wesbar 4-Pole Flat Connector #W787264. The part #HM38138 uses 18 gauge for all wires but the white that uses 16 gauge.

view full answer...

Answer 3

The older generations of the Wesbar submersible low-profile lights came with sealed light bulb capsules that are not replaceable. If your capsule is sealed, then your best option is to replace the lights with new lights like part #403026 and #403076.…

view full answer...

Answer 4

Yes, you should be able to use any 1157 bulb, such as #A1157B. So long as it is an 1157 bulb it will fit the socket and light up properly.

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Availability of Replacement Capsules for Wesbar Trailer Lights

Products Featured in This Question

Continue Researching