Replacement Hub for a Pop Up Camper w/ a 5 on 4-1/2" Lug Pattern and How to Clear the Cotter Pin
Updated 04/07/2026 | Published 04/06/2026 >
Products Featured in This Question
Question:
Hello, I just purchased an Idler Hub assembly kit that was recommend by one of your staff. Everything went on fine except for the ‘dust cap’. I tried hitting it in using a mallet and a piece of wood, then tried again with a driver tool. It still won’t go in. The cotter pin is not in the way. Any other suggestions? It seems like it fits when I push one side of it but the entire thing won’t go in all at once. Thank you!
asked by: Anthony
Expert Reply:
Hey Anthony welcome back! You're going to need to bend and possibly shorten the cotter pin to get the grease cap installed on the Trailer Idler Hub Assembly for 2K Axles item # AKIHUB-545-2-LF-2K. You'll almost need to wrap it around the castle nut to prevent interference with the grease cap.
Is the cotter pin too wide right now or is it sticking up to much?
You can add this information, along with any other questions you have, where it says Add Comment.
Product Page this Question was Asked From
Loadstar ST205/75D14 Bias Trailer Tire with 14" Black Wheel - 5 on 4-1/2 - Load Range C
- Trailer Tires and Wheels
- Tire with Wheel
- Bias Ply Tire
- Load Range C
- 205/75-14
- 14 Inch
- M - 81 mph
- 5 on 4-1/2 Inch
- Steel Wheels - Powder Coat
- Kenda
more information >
Continue Researching
- Q&A: Replacement Hub for a Pop Up Camper w/ a 5 on 4-1/2" Lug Pattern
- Shop: Kenda Karrier ST175/80R13 Radial Trailer Tire with 13" Black Mod Wheel - 5 on 4-1/2 - LR D
- Shop: Trailer Idler Hub Assembly for 2K Axles - 13" to 15" Wheels - 5 on 4-1/2 - Pre-Greased
- Shop: Kenda Karrier ST205/75R14 Radial Trailer Tire with 14" Black Mod Wheel - 5 on 4-1/2 - LR C
- Shop: Karrier ST175/80R13 Radial Trailer Tire w/ 13" White Mini Mod Wheel - 5 on 4-1/2 - Load Range D
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Search Results: trailer hitch
- Shop: Trailer Hitch
- Article: Trailer Wiring Diagrams
- Search Results: trailer tires and wheels
- Shop: Trailer Wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Comparing Kenda KR03, KR35, And KR53 Tires
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Search Results: trailer wiring
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Q&A: Which is Better for Highway Use 4.80-12 or 5.30-12 Trailer TIres
- Shop: Suspension Enhancement
- Shop: Power Mountain Tallboy Off-Road Bottle Jack - 8-1/2" to 37-3/4" Lift - 6 Tons
- Video: Hands-On with the Hub Saver Hub and Wheel Protector
- Article: How to Measure for Trailer Hitch Drop
- Video: Review of etrailer Trailer Hubs and Drums - Hub with Drum - AKHD-545-35-EZ-K
- Search Results: trailer jack
- Shop: Brake Controller
- Q&A: What is the Difference Between Load Range C and D ST175/80D13 Trailer Tires
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Search Results: trailer lights
- Shop: Gooseneck Hitch
- Q&A: Instructions to Wire a Trailer for Electric Brakes



Anthony
4/7/2026
The cotter pin is out of the way. I can’t upload a photo to a reply but the cap can slide in on that side. The cap doesn’t sit inside the hole, nothing is stopping it from going in. I watched the install video from your YouTube channel also but that cap goes on a lot easier.