Looking for Replacement Converter for 2007 Aliner Camper Trailer

Question

Question:

Hi there, I’m looking for a replacement converter for my 2007 Aliner camper trailer. It originally was equipped with a Centurion CS 2000. However, that was replaced with an Elixir ELX-30. I’m planning on using an AGM battery for now but will probably switch to Lithium battery in the future. Thanks for your input! Del

asked by: Del B

0

Expert Reply:

Hey Del, your Elixir ELX-30 is a 30 amp panel so for a replacement the best option would be the WFCO part # WF96FR. This is a similar panel that is rated for 35 amps and has a lithium panel so it will be ready for when you switch batteries. What batteries do you have now?

expert reply by: Jameson C

0

WFCO Panel
(click to enlarge)

Del B.

4/2/2026

Hi Jameson, thanks for your input! I was looking at another converter on your website, the Powermax PPC-30-45. I was wondering if that one would be another replacement choice. As far as my current battery, I have the renogy AGM. Thanks, Del

Jameson C.

4/2/2026

@DelB The part # PM47VR would work too but it is rated a little higher at 45 amps. Which as long as the wiring you have can handle the extra amperage it would work fine and would charge the battery a little quicker.

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Looking for Replacement Converter for 2007 Aliner Camper Trailer

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching