What are the Outside Flange Dimensions of the Ventline Exterior Wall Vent for RV Range Hood VE48VV?

Question

Question:

What is the outside deminsions edge of flange

asked by: Darryl B

0

Expert Reply:

Hey Darryl. The Ventline Exterior Wall Vent for RV Range Hood item # VE48VV has outside flange dimensions of 11-1/2" wide x 5-1/4" tall. It's designed to fit a 10-1/2" wide x 3-3/4" tall cutout.

What kind of motorhome or trailer do you have?

You can add this information, along with any other questions you have, where it says Add Comment.

expert reply by: Jerred H

0

VE48VV
(click to enlarge)

Answer 1

Hi Rolley, unfortunately the mounting bracket by itself is not available for the Dometic Soft Start for FreshJet Mechanical Air Conditioner Setup #DMC87RR.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 4

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 5

Hey Vic, thanks for reaching out. We will have the seal you need, but these Dexter 7K D70 axles are tricky because Dexter used two different seal sizes on their 7K axles and the info on the sticker actually doesn't tell us what seal it uses.…

view full answer...

Answer 6

Thanks for the picture! I checked with Progressive Dynamics the replacement power converter you need for your Parallax Series 7300 Model 7345 is the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers - 45 Amp item #PD4645V.

view full answer...

Answer 7

I verified with Lippert the correct replacement for your Power Gear slide-out motor 522735s is the following: - Replacement Gear and Motor Assembly for RV Slide Out - High Torque - Driver Side #LC386735

view full answer...

Answer 8

We do carry the lens for the Gustafson 12V RV Porch Light #277-000485 you were looking at with part #291-000002. I was able to find a dimensional drawing of the lens for your current light but I do have the measurements for the lens (pictured below).…

view full answer...

Answer 9

According to my research it looks like your 2013 Prime Time LaCrosse has a front porch light similar to the LED Porch and Utility Light for RVs #RVPLL13AB so if it matches the dimensions (see attached) then the Replacement Lens #APLL11AB is what we…

view full answer...

Answer 10

Thanks for the picture! The closest replacement we have for your Monarch 5129 Lights on your trailer is the Triple LED #CE44VR. This light measures 14" x 6-7/8" so it should completely cover your old mounting holes, though it's going to…

view full answer...

Answer 11

Are you absolutely sure that's the bolt pattern you have? Thats not a standard wheel bolt pattern so I'd be inclined to believe you have either a 5 on 5 inch or a 5 on 5-1/2 inch. I attached a picture that shows how you can easily measure…

view full answer...

Answer 12

The replacement lens for the Omega Single RV Dome Light with Switch #328-001-901XPW (and Double Version #328-001-902XPW) is part #328-89-255 on our site. It does have the same dimensions as what you mentioned but I'm not sure if it will be an…

view full answer...

What are the Outside Flange Dimensions of the Ventline Exterior Wall Vent for RV Range Hood VE48VV?

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching