Is There Curt Class III Hitch that Fits 2020 Lexus RX 350L

Question

Question:

Will this C73DR fit 2020 Lexus RX350L?

asked by: Thomas J

0

Expert Reply:

Hey Thomas, we have a Curt Class III hitch that does fit your 2020 Lexus RX 350 L with the part # C13394 but the part # C73DR does not fit the L versions of the vehicle so it would not work for you. What will you be using the hitch for?

expert reply by: Jameson C

0

Curt Hitch on Lexus
(click to enlarge)

Answer 1

The hitch you need for your 2021 Lexus RX 350 L is the Curt Trailer Hitch Receiver #C13394. This won't keep the foot operation from working but the hitch will get somewhat in the way of the sensors so you'll need to figure out the exact spot…

view full answer...

Answer 2

For the Curt T-Connector Vehicle Wiring Harness #C56217 on your 2021 Lexus RX 350L the connectors will be located in a different spot. The 10 pin connector should be located on the passenger side just below the taillight. The 4 pin connector will be…

view full answer...

Answer 3

TheCurt Trailer Hitch Receiver - Custom Fit - Class III - 2" #C13394 is a confirmed fit for your 2018 Lexus RX350L and not the RX350 which would use a different hitch #e94AR. We have a video of an install on a 2018 Toyota Highlander RX 350L to…

view full answer...

Answer 4

For the 2018 Lexus RX 350L, the Curt Trailer Hitch #C13394 is a confirmed fit and a great option. This hitch has a 2" receiver and 5,000 lbs of towing capacity with 500 lbs of tongue weight capacity, though you should check your owner's…

view full answer...

Answer 5

Yes, the Curt Trailer Hitch Receiver #C13394 will fit your 2022 Lexus RX 350 L as long as it doesn't have the Twin-Tip Exhaust. As far as the rear door kick sensor is concerned, we haven't heard anything about that but it isn't uncommon…

view full answer...

Answer 6

Hey Gary, We do not offer a completely hidden hitch for that vehicle. The hitches that we have are going to be visible to a point. We have a Curt Class 3 Hitch #C13394 that I recommend for that vehicle. You can see the 2 x 2 receiver, but you will…

view full answer...

Answer 7

In all likelihood your hitch like the Curt #C13394 is just slightly bent, which would cause the holes to be misaligned. Some people will use open steps for leverage, vices and even car jacks to apply controlled force to bend the hitch back. You will…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Is There Curt Class III Hitch that Fits 2020 Lexus RX 350L

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching