Does Promaster 7-Way Kit 22112 Work with Tekonsha Voyager ID

Question

Question:

Will this harness work with Tekonsha 90930 Trailer Brake Control Proportional?

asked by: John G

0

Expert Reply:

Hey John, yes the brake controller wiring that comes with the 7-way kit part # 22112 that you referenced will work with the Tekonsha Voyager brake controller part # TK26BR as it uses the same connector. Do you have the Voyager already?

expert reply by: Jameson C

0

Voyager Dial
(click to enlarge)

John G.

1/29/2026

No I haven’t bought either yet. But was looking for a small controller that’s out of sight like this. Do they sell as package?

Jameson C.

1/29/2026

@JohnG a package of the brake controller and the 7-way? We don't have those two together as a single part number but you can order them both individually and you'd be set.

Joshua

2/10/2026

@JamesonC Sorry I installed the REDARC that needed the install cable

Jameson C.

2/10/2026

@Joshua What vehicle do you have? I can see if there's a custom install harness for the Redarc that fits it.

See All (4) Replies to John G. ∨

Joshua

1/30/2026

This is a great setup. Make sure to order the coneector/harness for the controller. I also ordered the mounting plate. It was not needed but muliple peaple drive this vehicle and I wanted it more visible for the drivers.

Jameson C.

2/2/2026

@Joshua good advice!

John G.

2/7/2026

@Joshua thx for replying, what connector harness are you talking about. From what they replied the controller should plug into the supplied harness. Thank you John

John G.

2/7/2026

@JamesonC can you attach or let me know what harness Joshua is talking about? Wanna make sure I get everything I need. John

See All (4) Replies to Joshua ∨

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 12

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Does Promaster 7-Way Kit 22112 Work with Tekonsha Voyager ID

Continue Researching