Inside Diameter of Spindle Washer Included With etrailer Hub Bearing Kit

Question

Question:

BK2-100 what is the inside diameter of the tang washer

asked by: Rick B

0

Expert Reply:

Hey Rick! The Hub Bearing Kit # BK2-100 comes with the Replacement Spindle Washer # 5-101. This washer has a 1" inner diameter which will fit your standard #84 spindle.

What kind of trailer do you have?

expert reply by: Robin H

0

BK2-100 Spindle Washer
(click to enlarge)

Rick B.

1/19/2026

2004 Magic Tilt 3500 lb axles

Robin H.

1/19/2026

@RickB with 3,500 lb axles the # BK2-100 will be the right bearing kit.

Bob

1/20/2026

@RickB I just replaced bearings and seals on my 2023 Grandesign XLS with parts from ETRAILER just give the information they need and they are FAST at getting you the parts and correct ones. Never had a problem shopping with ETRAILER.

Jim

1/20/2026

Used for snowmobiling trailer. Bearing and race good. Upgraded to triple seal for moisture and salt in winter. Used original star nut lock and cotter pin. Grease seal triple lip DX49CR

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 9

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 12

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Inside Diameter of Spindle Washer Included With etrailer Hub Bearing Kit

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching