Instructions for Using Optronics Trailer Wiring Kit # TL29BK
Updated 06/26/2014 | Published 06/25/2014
Question:
Hi, I just purchased Optronics Trailer Taillilght Kit, part # TL29BK I cannot seem to find the instructions. Can you send me a .pdf of the instructions for this product? I cannot find a download instruction on the product page. I looked on the Optronics website and found the kit but did not find any instructions to download there either. Thank you. Karsten Shields
asked by: Karsten S
Expert Reply:
Optronics doesn't offer instructions for the # TL29BK trailer taillight kit. However, if you click the link I provided to the the trailer wiring help article, you'll see a wiring diagram showing how the kit would be used to wire a trailer.
The wiring system shown in the diagram is more elaborate than what you'd have, so you'd ignore all the wire colors but the white, green, yellow and brown.
The green wire feeds the right turn/brake lamp. From the front of the trailer, it would run along the right side of the trailer, and the wire would push into the corresponding slot in the back of the taillight. The yellow wire feeds the left turn/brake lamp and would run along the left side. The wire would plug into the rear of the lamp. The white wire would ground to the trailer frame, usually to the trailer tongue and the brown wire would run down one side of the trailer, pick up the side marker light, continue to one taillight, then the next, and around the other side to pick up the final marker light.
Product Page this Question was Asked From
Standard Trailer Light Kit with 25' Wire Harness
- Trailer Lights
- Tail Lights
- Brake/Tail/Turn
- License Plate
- Marker
- Square
- Surface Mount
- Non-Submersible Lights
- Incandescent Light
- 5L x 4-1/2W Inch
- Amber
- Red
- Optronics
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Trailer Wiring
- Search Results: tail light converter
- Search Results: trailer converter
- Video: Complete Breakdown of the Standard Trailer Light Kit with 25' Wire Harness
- Shop: Submersible, Under 80" Trailer Light Kit with 25' Wiring Harness
- Video: Bonded 4 Wire: The Breakdown
- Shop: Vehicle Tow Bar Wiring
- Shop: Standard Trailer Light Kit with 25' Wire Harness
- Q&A: Why Choose a Powered Taillight Converter Over a Non-Powered Model
- Q&A: Troubleshooting Running Light Circuit Not Working On Right Side of Trailer
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: etrailer Trailer Wiring Junction Box - 7 Terminal
- Shop: Trailer Wiring Junction Box - 7 Color Coded Terminals - ABS
- Shop: Curt 2-to-3 Tail Light Converter for Towed Vehicles w/ Incandescent Tail Lights
- Shop: 16 Gauge, 4 Conductor Bonded Parallel Wire - Per Foot
- Video: How to Install the etrailer Trailer Hitch Receiver on a 2011 Toyota RAV4
- Video: Ultimate Overview of the Standard Trailer Light Kit with 25' Wire Harness
- Article: Trailer Wiring Diagrams
- Q&A: Difficulty of Installing Optronics Trailer Light Kit # TL29BK On Small Trailer
- Q&A: Wiring a 2011 Victory Motorcycle and Trailer for Towing
- Q&A: Install Video For Standard Trailer Light Kit # TL29BK
- Q&A: Correct Wiring for Optronics LED Trailer Lights # STL22RB
- Shop: Trailer Hitch
- Search Results: trailer lights
- Video: The Low-Down on the Electrical Cable Hatch for RVs
- Video: All About the Valterra Electrical Cable Hatch for RVs
- Search Results: 13 inch wheels
- Q&A: All Trailer Lights Blink When One Turn Signal Is Activated
- Search Results: trailer wiring harness kit
- Search Results: trailer hitch
on Trailer Lights
