Offset of the Aluminum HWT Split Spoke Trailer Wheel # AM22318HWT

Question

Question:

I would like to know how the offset on the aluminum wheel compares with the factory steel 12inch wheel measured from the back, hub face to rim edge face? Thanks

asked by: Ron

1

Helpful Expert Reply:

The Aluminum HWT Series Split Spoke Trailer Wheel # AM22318HWTB that you referenced has a 0 offset like nearly all trailer wheels do. Chances are your current trailer wheels have a zero offset as well, but you could measure to know for sure.

expert reply by: Jameson C

1

Answer 1

Hey Marc, the difference between the two grease seals is that the part #34823 is sold individually and the part #RG06-010 is sold in pairs. Aside from that they are the exact same seal. How many seals are you in need of?

view full answer...

Answer 2

I do have a solution I can offer you, but the Atwood AT82543 is no longer available. It was discontinued back in 2017. The closest option we have to replace your Atwood 82543 actuator is part #DM72VR. However, it doesn't have the reverse lockout…

view full answer...

Answer 3

The issue your friend is having with his trailer is a mechanical one so we can rule the vehicle out. The reasoning for this is because the only way you would have been able to back up the trailer with using just a 4-way trailer connector is if you…

view full answer...

Answer 4

Hello Fred; to add a 4-way to your 2023 Explorer XLT you need the Curt T-Connector Vehicle Wiring Harness #C56093. This plugs into the connection points in your rear cargo area. You will also need the Curt Trailer Connector Adapter #C57187 which will…

view full answer...

Answer 5

Hello Bob, thanks for reaching out. The 5th wire your trailer has is a reverse light circuit. We do sell a wiring kit that will allow you to add a reverse light circuit to your vehicles 4-flat to upgrade it to a 5-flat. For that, you can use the…

view full answer...

Answer 6

I reached out to HWT who makes the Aluminum HWT Series S5 Trailer Wheel - 12" x 4" Rim - 4 on 4 #AM22318HWT you were looking at which uses a 1/2" x 20 wheel stud and they mentioned it will work just fine on your M12x1.25mm studs. I…

view full answer...

Answer 7

There are so many possible tire and wheel combinations that manufacturers have chosen to provide only the most common set ups. But a local tire shop will be able to mount a tire on a wheel for a nominal fee. For a 145/R12 Load Range E tire we have…

view full answer...

Answer 8

Based on the number 471750 that you gave the correct replacement grease seal will be the part #34823. This seal has an inner diameter of 1.25 inch and an outer diameter of 1.983 inch.

view full answer...

Answer 9

Hey Bruce, thanks for the information. The Kenda KR25 Radial Trailer Tire with 12" Aluminum HWT Wheel item #AM31208HWT will indeed work with lug bolts. However, they must be 1/2-20 60-degree conical cone seat lug bolts not the standard ½-20…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

Hey Dave, for a saltwater boat trailer, powder-coated wheels wouldn't be my first choice, but they can still last quite a while if you're good about rinsing them thoroughly after each launch and sealing any chips or cracks in the finish as…

view full answer...

Offset of the Aluminum HWT Split Spoke Trailer Wheel # AM22318HWT

Featured Help Information

Miscellaneous Media

Continue Researching