Can Warning Light On Fusion LED Hardwired Trailer Light OPT27NR Be Used As A Turn Signal?

Question

Question:

Hello. I’m looking at STLW316MGHB. Can the amber warning light portion also be used as a turn signal? Thank you

asked by: Geoff M

0

Expert Reply:

Hello Geoff, thanks for reaching out. Yes the warning lights on the Fusion LED Hardwired Trailer Light # OPT27NR can be wired to the turn signals if you wish. Just make sure the wires are connected to the correct circuit. The green wire is for the amber warning light.

expert reply by: Jesse M

0

Jesse M.

12/8/2025

Hey Geoff, how did things go wiring the amber warning lights on the Fusion LED trailer light to your turn signals? Your update could make it easier for others trying the same setup.

Answer 1

The Optronics #BUL602CRB is a 2-function lamp, taillight and back up lamp so it won't function in the fashion you're wanting. The good news is that we have a grommet mount lamp that will provide stop/turn, taillight and back up lamp…

view full answer...

Answer 2

It can definitely be a very confusing subject when trying to determine the correct size winch and strap for your boat. The important thing to remember is that you are not lifting the entire weight of the boat but rather pulling it across the bunk…

view full answer...

Answer 3

You will need to locate the safety chains before the cut that is made to install the Fold-Away Coupler Hinge, #FHDPB330301, to be in compliance with DOT regulations. Normally the chains are welded to the bottom or side of the trailer framing, and ran…

view full answer...

Answer 4

Both the LED Trailer Mini Clearance #MCL10AKB and Uni-Lite LED Clearance #MCL11RKB will require an 11/16" hole for mounting. These both use the same Grommet #A11GB.

view full answer...

Answer 5

I checked with the manufacturer, and the Optronics Tri-Bar LED RV Tail Light is indeed flush-mounted. The correct part number is the following: - Tri-Bar LED RV Tail Light #OPT27FR

view full answer...

Answer 6

The outside diameter of the 2" Round Grommet #A54GB you referenced is 2-3/4". This grommet is used with 2" round lights such as the GloLight LED #MCL155RB (Red) or GloLight LED #MCL155AB (Amber). You will also need a 2-wire pigtail to…

view full answer...

Answer 7

There are a number of things you will need if you want to re-wire your boat trailer to use LED lights and you should start with Junction Box #3375601100 and 7-Way #HM20041. Keep in mind you will also need Ring Terminals #44-5310A and Loom Clamps…

view full answer...

Answer 8

For a brake controller I would recommend the Prodigy P2 Brake Controller part #90885. This is our best selling brake controller because of how well it works and how easy it is to setup. This is a proportional brake controller that senses the amount…

view full answer...

Answer 9

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 10

Hello Marcy, thanks for reaching out. We do have a good replacement option for you. Take a look at the Bulldog Square Jack #BD182804. This has a 27-3/8" retracted height and extends out to 39-1/2". It has a 10K lift capacity and 12K support…

view full answer...

Answer 11

The reverse light pin on a traditional 7-way trailer connector, like part #PK11893 or a factory connector if that's what you have on your 2018 Ram, is the center pin. Take a look at the picture I attached that shows all the pin functions. To add…

view full answer...

Answer 12

I more or less agree with you. The Fulton Fold-Away Hinge Kit for 3 x 3 inch Trailer Tongue - Weld-On, item # FHDPW330300, is a cleaner look and if you got a bad weld job you would not have a safe setup. I have done some welding, I am in no way a…

view full answer...