Parts Needed to Add 7-Way and Install Brake Controller 2015 Ram ProMaster 1500

Question

Question:

Hi, I need to equip a 2015 RAM ProMaster 1500 van for towing with a 7 blade connector. Will this fit? I’ll also need a brake controller Redarc?. Thanks

asked by: Rob

0

Expert Reply:

Hey Rob, since your 2015 Ram Promaster 1500 doesn't have a 7-way currently that would indicate that it does not have the factory tow package and you would need to go a different route to install a 7-way and brake controller.

The first thing you would need is a 4-way with the part # 118618 which installs by plugging inline with the taillight connectors at the rear of your Promaster. Then to convert that to a 7-way you would also need the part # ETBC7 which comes with everything for that as well as wiring in a brake controller like the Redarc Tow Pro Liberty part # RED52VR.

What are you planning on towing?

expert reply by: Jameson C

0

Rob

11/10/2025

Thanks, I’ll be towing a travel trailer about 4500lb. The VIN says it has “factory tow wiring” and it has a “tow/haul” button on the dash.

Jameson C.

11/10/2025

@Rob That's interesting. You might check under the rear bumper for the square connector that a 7-way would plug into.

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 12

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Parts Needed to Add 7-Way and Install Brake Controller 2015 Ram ProMaster 1500

Products Featured in This Question

Continue Researching