What Size is the Hole for the Shank of the Hitch Ball on the etrailer Ball Mount Kit?

Question

Question:

etrailer Ball Mount Kit e83ZV dos this have a 1 shank hole for a ball?

asked by: Carlos A

0

Expert Reply:

Hey Carlos. The etrailer Towing Kit w/ 2" Ball Mount item # e83ZV has a 1-1/4" ball hole diameter for the shank and fits a 2" receiver. This kit includes a 2-5/16" hitch ball. It also has a hitch pin and a carrying bag. The ball mount itself has a 7,500 lbs capacity and offers a 2" drop.

The etrailer Ball Mount Kit item # e83ZV comes with everything you need to tow a trailer. Are you needing just a ball mount with a 1" ball hole diameter? If so check out the Curt item # C45230.

You can add this information and any other questions you have where it says Add Comment and I'll be happy to answer them.

expert reply by: Jerred H

0

Carlos

11/3/2025

I’m looking for class V min hitch with a 1” ball shank hole with either no drop or 4”’drop The problem I’m having is finding a 1” hole Weigh-safe has 2” drop hitch 10000 rating with a 1500 pin weight with a 2” drop… other then that I’m not aware of anything else

Jerred H.

11/3/2025

@Carlos Hey Carlos. The Convert-A-Ball Ball Mount item # AMSC2 also has a 1" ball hole diameter like the Weigh-Safe item # WS56KR you mentioned. It's also going to be limited to 10,000 lbs. You can use the Hitch Ball Bushing - 1-1/4" to 1" - Zinc item # F-2 on the Curt Heavy Duty Forged Ball Mount item # C45341. It has a 17,000 lbs capacity, a 4" drop, and fits a 2" hitch. The bushing will reduce the shank hole from 1-1/4" to 1" in diameter.

Answer 1

Hey Glenn. I went down to the warehouse and measured the BulletProof Hitches 2" Hitch Ball item #BPH43RR. From the bottom of the shank to the top of the hitch ball is 5-1/4". This is a 2" hitch ball with a 10,000 lbs capacity. It has a…

view full answer...

Answer 2

You've got good instincts. I recommend going with a ball mount that has a 2 inch rise for the exact reason you mentioned, the truck will settle a bit with the tongue weight and any cargo weight. The ball mount we offer with a 2 inch rise is the…

view full answer...

Answer 3

When we installed 2-inch Curt Class III hitch #13354 on a 2009 MDX we found that the top of the receiver opening was indeed 17-inches above ground, although this can vary slightly from car to car depending on the amount of tread wear and factors like…

view full answer...

Answer 4

There are very few trailer hitch balls with a rise, and all of them are made of chrome-plated steel, including the 2" trailer hitch balls. Both 2" hitch balls have a 6,000 lb capacity and 1" diameter shank with the difference being the…

view full answer...

Answer 5

The ball mount that comes with the Curt part #C45036 has a 1 inch diameter ball hole which means you can install the hitch ball part #C40033 in place of the included ball and have the same diameter hitch ball but 1 inch taller.

view full answer...

Answer 6

A vise would be the best solution to hold the 2" Hitch Ball #C40033 while you torque down the nut.

view full answer...

Answer 7

Hi Greg; we do carry a hitch and wiring for your 2025 Sienna. The best hitch is the etrailer #e56RR. This has a 2" receiver, bolt-on installation, and a matte black powder coat finish. It also comes with a limited lifetime warranty. For wiring…

view full answer...

Answer 8

This is a great question that there isn't exactly a great answer for. Hitch extenders not only put the weight further away from the hitch which would increase the leverage on the hitch, but they also add movement to the assembly which will…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 11

Hey Mark, thanks for reaching out! The #331-TPSI-001 mounting panel is a universal-fit part rather than a custom-fit replacement for the blank switch panel in your 2025 Subaru Outback Touring XT. It measures 1-1/4" tall x 1" wide, so…

view full answer...

Answer 12

Hey Nick congrats on the new car! The bottom portion of the receiver for the Curt item #C69VV sits 11-3/4" above the ground when installed on your 2025 Subaru Outback Premium. If you're worried about ground clearance, I recommend installing…

view full answer...

What Size is the Hole for the Shank of the Hitch Ball on the etrailer Ball Mount Kit?

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching