How Accurate is the Sherline Trailer Tongue Weight Scale?

Question

Question:

What is the accuracy of this scale?

asked by: Ron B

0

Expert Reply:

It's extremely accurate Ron. The Sherline Trailer Tongue Weight Scale item # 5780 has been tested by the manufacturer to be within 2%-3% of the scales range. We've had quite a few customers compare it to weights they've gotten from CAT scales.

What kind of trailer do you have?

expert reply by: Jerred H

0

Sherline Trailer Tongue Weight Scale
(click to enlarge)

Jerred H.

11/13/2025

Hey Ron, how did the Sherline tongue weight scale perform when you tested it with your trailer? Your results could help others see how close it reads compared to larger scales.

Answer 1

Hey Ben, the total height of the etrailer jack part #e34RV when fully retracted is 16-1/2 inches. Would that fit in the area you have between the fender and rear supports?

view full answer...

Answer 2

The most stable and heavy duty scissor jacks we offer are the Ulftra Fab set part #UF48-979002. We've had customers install the JTs Strongarm kits like part #LC191025 on them without having to drill so these would have correct bolt size.

view full answer...

Answer 3

Hey Kevin, are you looking for stabilizer jacks like the Stabilizer Jacks #TJ01RT-HD which pops down. This particular jack has a 650 lb lift capacity, 6 1/4" of travel, and each jack can support a maximum of 1,000 lbs. If you're looking for…

view full answer...

Answer 4

Hey Josh, the dimension for both jacks that you are looking for is the bracket height. This is the distance from the center of the jack's mounting bracket down to the ground when extended/retracted. On the shorter part #e34RV the bracket height…

view full answer...

Answer 5

Hey Thomas, what kind of trailer do you have? Planning any cool trips when the weather warms up? The etrailer 2 Swivel Jacks w/ Bolt-On Mounting Plates #e34RV measures 20 1/2" from the bottom of the jack foot to the underside of the 90°…

view full answer...

Answer 6

I recommend just using some stabilizer jacks to help keep your trailer from tilting while you're loading your ATV. You can use something as simple as the Ultra-Fab Stackable Stabilizers #UF48-979003 (Qty 2) or #UF48-979004 (Qty 4), OR you can use…

view full answer...

Answer 7

Hello again Frank; tongue weight is typically 10-15% of your trailer weight. At 5,400 lbs you could go over the max 800 lb tongue weight of the #FA94-00-0800 but that probably isn't the case here. If you really want to be sure you could always…

view full answer...

Answer 8

Hey Tony! The Big Truck Big RV Tongue Weight Scale for Trailers - 1,000 lbs #BTBRV004 is not adjustable. It has a fixed height of 17-1/4". At that height, and the 1,000 lb capacity, you will be able to get a measurement on a lot of different…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

How Accurate is the Sherline Trailer Tongue Weight Scale?

Continue Researching