What is Overall Height of etrailer Jack # e34RV When Fully Retracted
Updated 03/04/2026 | Published 03/02/2026
Question:
What is the total height of the jack? Im trying to figure out if it will mount between the fender and rear supports on my off road trailer. Thanks
asked by: Ben
0
Expert Reply:
Hey Ben, the total height of the etrailer jack part # e34RV when fully retracted is 16-1/2 inches. Would that fit in the area you have between the fender and rear supports?
expert reply by:
Jameson C
0
Trailer Jack
(click to enlarge)
(click to enlarge)
Product Page this Question was Asked From
etrailer 2 Swivel Jacks w/ Bolt-On Mounting Plates - Sidewind - 10" Lift - 3,000 lbs
- Trailer Jack
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- Side-Mount Jacks
- Swivel Jacks
- Sidewind Jack
- 2001 - 3000 lbs
- Manual Jack
- 10 Inch Lift
- Bolt-On
- With Rectangle Foot
- etrailer
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Suspension Enhancement
- Search Results: straps
- Search Results: wheel straps
- Shop: Timbren Rear Suspension Enhancement System
- Q&A: Can Spacers Be Added to Timbren SES To Make Smaller Gap
- Shop: Spacer Kit for Timbren Suspension Enhancement System
- Search Results: ark drop down corner rv stabilizer jacks
- Search Results: timbren
- Search Results: timbren vehicle suspension
- Q&A: Timbren SES for 2021 Nissan Frontier Hauling Commercial Mower and Towing Utility Trailer
- Shop: Square Drop Leg Stabilizer Jack - 18" Travel - 2,000 lbs - Qty 1
- Search Results: draw~tite max~frame trailer hitch receiver ~ custom fit ~ class iv ~ 2
- Search Results: 2 jacks camper jacks
- Shop: Spacer Kit for Timbren Suspension Enhancement System
- Video: Feature Breakdown: Spacer Kit for Timbren Suspension Enhancement System
- Video: Choosing the Right Vehicle Suspension Upgrades
- Shop: etrailer 2 Swivel Jacks w/ Bolt-On Mounting Plates - Sidewind - 10" Lift - 3,000 lbs
- Q&A: Extended and Retracted Dimensions of the etrailer 2 Swivel Jacks w/ Bolt-On Mounting Plates
- Shop: Stabilizer Jack - 6-1/4" Drop Leg Travel - 18" - 650 lbs - Qty 1
- Shop: Trailer Hitch
- Q&A: What is Distance from Mounting Bracket to Ground on etrailer Jacks e34RV
- Shop: Spacer Kit for Timbren Suspension Enhancement System
- Shop: Fifth Wheel Hitch
- Video: An In-Depth Look at the Ultra-Fab Ultra Scissor Jacks
- Video: Review of etrailer Trailer Jack - Dual Swivel Jack Kit with Mounting Plates - e34RV
- Video: A Closer Look at the etrailer Swivel Jacks with Bolt-On Mounting Plates
- Q&A: Scissor Jacks for Rockwood Mini to Use with JTs Strongarm Kit
- Q&A: Recommended Replacement Pop Down Stabilizer Jack for a 2003 Thor Tahoe Lite Travel Trailer
- Q&A: What is Bracket Height for etrailer 2 Swivel Jacks e34RV and e94RV
- Video: A Closer Look at the Stabilizer Jack
Edward L.
3/4/2026
I got those jacks last year because my one bolt on jack failed. This e34RV jack system has worked out for me due to 2 jacks not just one! They appear to be very rugged and balanced my trailer a lot better than one! The double system does require a bit more work to crank them up and down. The only thing I’m frustrated with is that they wobble a bit more than the former jack (sloppy). My jacks were set up to use the bolt on brackets due to not having a welder, and they are very secure. I also have to be careful to not back up the trailer a lot real sharp or I’ll smack the handles. They have been real good all last mowing season.