Is Dexter Grease Seal for 12" x 2" Hubs Manufactured By Dexter

Question

Question:

Are these OEM manufactured by Dexter or are these aftermarket parts?

asked by: Thurston

0

Expert Reply:

Hello Thurston; the Dexter Grease Seal for 12" x 2" Hubs # DX72UR is manufactured by Dexter and matches their OEM parts.

expert reply by: Robin H

0

Dexter Grease Seal for 12" x 2" Hubs
(click to enlarge)

Robin H.

9/29/2025

Hey Thurston, did the Dexter Grease Seal work well for your needs? I'm curious to know because it could help others who are looking for OEM parts.

Answer 1

Hey, Terry. Thanks for reaching out. AL-KO wasn’t always consistent with their axle components, so the best way to find the correct seal is by measuring. I know removing and measuring the existing seal isn’t always easy, but if you can get the outer…

view full answer...

Answer 2

Yes, we do Steve! It is the Grease Seals 10-36 (pair) item #RG06-070. This is also a pair of seals with a inner diameter of 2.250" and an outer diameter of 3.376".

view full answer...

Answer 3

Hey Jared! Thank you for providing those part numbers. You have #LM67048 outer and #25580 inner bearings with a #DX72UR (K71-305-00) grease seal. The correct Timken bearing kit is the #TMK72VR. If you need anything else feel free to reply below.

view full answer...

Answer 4

The Tru Ryde grease seals you mentioned, part #RG06-70 are indeed a replacement for the 10-036-00 Dexter seals. They would work great for your application.

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Is Dexter Grease Seal for 12" x 2" Hubs Manufactured By Dexter

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching