Dimensions of the Timbren Heavy-Duty Axle-Less Trailer Suspension # ASR2KHDS03

Question

Question:

Is there a complete detail dimension on this on this . I,m in integrate this into my pop-up camper. Fender wells are cannot be alter. so if dimensions on this part are available it would be a great help .Thanks

asked by: SAM

1

Helpful Expert Reply:

I attached a picture that has all of the dimensions for the Timbren Heavy-Duty Axle-Less Trailer Suspension # ASR2KHDS03 listed.

expert reply by: Jameson C

1

click to enlarge

Answer 1

Hey Scott. The Lock N Roll item #336TS526 you were looking at isn't designed for that but I have something that is. For a 2-1/2 square tongue you'll want the Lock N Roll Articulating Channel Tongue Trailer Coupler item #336TS506. This will…

view full answer...

Answer 2

A standard trailer dolly like #RA20 is not directly compatible with the Lock N Roll hitch system. There is not a dolly designed to work with that system, however if you were to use a similar system with the ability to attach to a hitch ball, then a…

view full answer...

Answer 3

Hello Andrew, Time to make the switch to Axle-Less, you won't regret it! The Timbren Axle-Less Trailer Suspension System - 4" Lift Spindle - Off-Road Tires - 5,200 lbs #T99GR will work with the Easy Grease Trailer Hub and Drum…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Dimensions of the Timbren Heavy-Duty Axle-Less Trailer Suspension # ASR2KHDS03

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching