Trailer Hitch For A 2011 Lexus IS 250 or IS 350

Question

Question:

I am looking for a hitch for a 2011 Lexus IS250C or IS350C My father owns both The intent is to haul a light weight mobility scooter on a rack or lift. Thanks!

asked by: Mike K

0

Expert Reply:

Hi Mike!

The Curt # C11372 hitch you found will actually fit both the 2011 Lexus IS 250 and the IS 350, which makes it easier. However, it should be noted that this is a Class 1 hitch and has 200 pounds of tongue weight.

Do you already have the carrier/rack?

expert reply by: Lazer S

0

Lazer S.

8/7/2025

Hey Mike, Did you end up getting the Curt hitch for your Lexus to haul the mobility scooter? I'm curious if it worked out for you, as it could really help others in a similar situation.

Mike K.

8/8/2025

We found a lighter smaller scooter dad is trying to carry it on the passenger seat, If that is too cumbersome we will do the hitch. The next concern is to find a rack for a 1 1/4 receiver to avoid modifying the hitch.

Lazer S.

8/8/2025

@MikeK Makes sense. With the # C11372 hitch being a Class 1, it will limit you a bit, but the 19x47 Curt Cargo Carrier for 1-1/4" and 2" Hitches - Steel - 300 lbs # C18110 will fit without modification and gives you a good amount of room. We may have something that will work better than that if you need, but just let me know if you decide to go that way! Always here to help! : )

Answer 1

I do have a bike rack to fit your vehicle. Unfortunately, it will not be a hitch bike rack. I took a look at the owner's manual for your 2022 Lexus ES 350. Oftentimes, the availability of a trailer hitch is based upon whether you can use your…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 5

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Hey Adrian! The higher capacity for the B&W #BW47BR and Curt #C77MJ comes from the construction. The B&W hitch weighs 45 lbs and then the Curt and Trailer Mate #TMT54FR both weigh 32 lbs. The Trailer Mate does sit just a tad higher compared…

view full answer...

Answer 10

It sure is Rob, and congrats on the new SUV. The Oris Trailer Hitch with Detachable Hitch Receiver item #TS76VR is definitely comparable to the Stealth Hitches item #SH87FR. It's got the same kind of removable receiver that works great with a…

view full answer...

Answer 11

Though the Curt # C13409 and Draw-Tite #76271 are nearly identical to each other, there are a few subtle differences. First being where they sit once installed. The will both have the exact same height of 14-1/2 inches, but the Draw-Tite #76271 will…

view full answer...

Answer 12

Hey David, thanks for reaching out. Yes, the Curt Trailer Hitch Receiver #C82RJ will indeed fit the 2027 Kia Telluride. This hitch is still in the pre-order phase, but it is being going to fit both the 2026 and 2027 Telluride. Right now, we are…

view full answer...

Trailer Hitch For A 2011 Lexus IS 250 or IS 350

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching