Replacement Mounting Plate for MORryde RV Steps stp-202mh-226-09

Question

Question:

i have a set of morryde steps im needing a new mounting plate but not sure what one to get. on the sticker under steps has stp-202mh-226-09 wo:st74217

asked by: Mason

0

Expert Reply:

Hey Mason, thanks for the info on your current steps. Based on seeing that the correct replacement mounting plate is the part # MR79DR that you referenced.

expert reply by: Jameson C

0

Jameson C.

8/7/2025

Hey Mason, did the replacement mounting plate work out for your MORryde steps? I'm curious to know if it was the right fit for you, as it could help others in a similar situation.

Answer 1

Yes, the MORryde StepAbove RV Steps with Strut Assist like #MR85RR can use the removable mounting plate. It isn't compatible with the struts but you already plan to remove them so that won't be an issue. Assuming you have a 26-28" wide…

view full answer...

Answer 2

Hey Dan! That is definitely the struts wearing out. You can replace them with the #MR56DR. If you need anything else don't hesitate to reach out in the comments below.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

Hello Al, Great question. I totally get why you’d want that option, and I wish it were available, but there is not a 6" console designed specifically for this couch. Instead, to get a console in the middle, you would need to add the Thomas Payne…

view full answer...

Answer 10

Hey Al, Since your Dexter #9919860 is a 3,500lb axle you'll need grease seals #RG06-050 which come as a pair. I'd get 3 pairs (6 seals) that way you have an extra incase one goes in funky and bends (I've repacked hundreds of hubs and it…

view full answer...

Answer 11

Hello Bruce, Thanks for writing in! Using butyl tape between the trailer body and the Single Axle Jeep Style Trailer Fender - Diamond Plate Aluminum - 13" to 15" #HP96VR is exactly the route I would go. It stays flexible, creates an…

view full answer...

Answer 12

Hey Nick, thanks for reaching out. Yes, the Replacement Fabric for etrailer Powered RV Awnings #e96QV will work with other brands of awning like Solera or Dometic which are what we commonly see on campers like your 2011 Forest River Cherokee 29U. The…

view full answer...

Replacement Mounting Plate for MORryde RV Steps stp-202mh-226-09

Product Page this Question was Asked From

Continue Researching