Do I Have to be Totally Straight When Connecting to B and W Continuum Weight Distribution

Question

Question:

Can I hook-up or disconnect on a left or right angle with the Continuum?

asked by: Mark

0

Expert Reply:

Hey Mark, B and W recommends that your trailer be level side to side and totally straight when connecting to the B and W Continuum part # BW78FR. I would assume there's a little bit of wiggle room with that but nothing significant. Are you concerned about uneven campsites?

expert reply by: Jameson C

0

Mark

6/11/2025

No short pad at home.

Jameson C.

6/11/2025

@Mark You mean like driveway?

Mark

6/15/2025

@JamesonC no short concrete pad on side of garage with tree at front of pad. Pad was put in for 24 ft. 5th wheel it would be easier to come in on little angle but straight should be ok. The new travel trailer is 28 ft. Plus tongue.

Jameson C.

6/16/2025

@Mark I'd probably pull it out onto flat before setting up the Continuum then.

See All (5) Replies to Mark ∨

Answer 1

Hello Dennis, That is definitely something you will want to check with your setup. The B&W Continuum #BW78FR will sit about 9 inches below your trailer frame once installed, so you will want to measure from the ground to the bottom of the frame…

view full answer...

Answer 2

Welcome back Daniel. From the hitch pin to the center of the hitch ball is 11-3/8" on the 2" shank included with the B&W Continuum item #BW78FR. If that isn't long enough to clear your Hummer's spare tire, we have the B&W…

view full answer...

Answer 3

The B&W Continuum #BW78FR and the Reese Strait-Line #RP66083 are both great systems. The B&W Continuum is going to be easier to set up, but as far as sway control goes, I definitely have to give the edge to the Reese Strait-Line. The…

view full answer...

Answer 4

That is definitely a feature which worries me about the B&W Continuum Weight Distribution System #BW78FR. While there is not a specific measurement I can give you as the bars move up and down depending on the load placed on the bars, B&W…

view full answer...

Answer 5

Hey Ray! Yes, the B&W Continuum Weight Distribution System w/ Sway Control #BW78FR is the right model for your Serenova 160LG. The only other option I might consider is the #BW94BR with the extra long shank. This will push back the trailer an…

view full answer...

Answer 6

Hey Lance, That does sound excessive, but the B&W Continuum #BW28FR is a bit of a different animal when it comes to how it operates so I do recommend sticking to the rules laid out by B&W. It wouldn't be a bad idea to have a grease gun…

view full answer...

Answer 7

Hey John, in that situation yes I would recommend using the trailer jack to see if you can raise the rear of the truck a bit to allow it to sit more level. Unless the incline was really steep then that wouldn't work as that would be a lot of…

view full answer...

Answer 8

Hey, Brent. Thanks for sharing the GVWR and hitch weight. Based on that information, yes, the Weigh Safe True Tow Weight Distribution Hitch part #WS49MR will work for your setup. One thing to keep in mind is that the 1,400 lb hitch weight rating does…

view full answer...

Answer 9

Sorry Chris but they have not. I checked with B&W and they only offer the B&W Continuum Weight Distribution Head Assembly item #BW68FR that comes with the B&W Continuum Weight Distribution System item #BW28FR.

view full answer...

Answer 10

The B&W Continuum Weight Distribution System part #BW78FR is not compatible with any other weight distribution system shank. The hole spacing on the shank for the head adjustment is 1-1/2" on center which is more than the 1-1/4"…

view full answer...

Answer 11

Yes, this is normal. The Timbrens will engage first when you hook up the trailer and the weight distribution hitch will then work with the remaining sag. Just make sure you're not overloading your truck's tongue weight capacity and the weight…

view full answer...

Answer 12

The best way to reduce vehicle sag and trailer sway would entail the use of a weight distribution system. A weight distribution system works by distributing the weight on the rear axle of the tow vehicle across the entire platform. This will allow…

view full answer...

Do I Have to be Totally Straight When Connecting to B and W Continuum Weight Distribution

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching