What is Purpose of Vertical Bolt Above Hitch Opening of Curt Hitch 13230

Question

Question:

I bought 13230 hitch for my 2007 dodge truck and was able to put it on with no issues, however I am confused by the 1/2 screw that goes into the TOP center using 1/2 allen wrench. What is the purpose of the screw. It seems to serve real no purpose in the operational use of the hitch.

asked by: David

0

Expert Reply:

Hey David, that bolt may not do much but it is designed to provide some additional support for the Curt hitch # 13230.

expert reply by: Jameson C

0

Install Diagram Curt Hitch
(click to enlarge)

David B.

6/5/2025

Thanks for the reply. It seems that my center hole is too big to provide and “link” between the bumper and the trailer hitch itself.

Jameson C.

6/5/2025

@DavidB That's odd, so the hole in your bumper is too big for the bolt to have anything to grab onto and would slip right through it?

Davidb

6/13/2025

@JamesonC yes

Jameson C.

6/16/2025

@Davidb Did someone by chance drill it out bigger to fit a larger diameter shank hitch ball?

Answer 1

We have 3 hitches that will fit your 2008 Dodge Dakota. All three hitches will require you to remove your factory trailer hitch. I recommend the Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2" #75251 which has the very…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 7

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 8

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

What is Purpose of Vertical Bolt Above Hitch Opening of Curt Hitch 13230

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching