Recommended Highest Rise Ball Mount for a 1-1/4" Hitch
Updated 09/29/2025 | Published 05/15/2025
Products Featured in This Question
Question:
A friend had a curt class 1, 2000 1 1/4 hitch mounted on her 2014 ES 350 Lexus. The trailer ball mount needs a 2 ball. It needs to be at least 8 from the rear of the hitch and have an approx. rise of 8-9. Can you give me a part/parts number that will give me that combination? Thank you,
asked by: Larry T
Expert Reply:
Hey Larry that's quite a bit of rise! They don't make those for 1-1/4" hitches but I can get you closeish.
You'll want to start with the Curt Class I Drawbar item # C45024. It has a 5" rise from the top of the inside of the hitch receiver. This ball mount extends out 9-9/16" from the hitch pin hole to the center of the hitch ball.
For a hitch ball, you'll want to use the Curt RockerBall Shock Absorbing 2" Hitch Ball item # C94CR. This will gain you an extra 1-1/2" of height over a standard hitch ball. This 2" hitch ball would get your total height to 6-1/2". That's to the base of the hitch ball where it connects to the coupler.
What kind of trailer is your friend going to be pulling?
Product Page this Question was Asked From
Curt Class I Drawbar - 5" Rise - 9-9/16" Long - 2,000 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- Steel Shank
- Rise - 5 Inch
- Fits 1-1/4 Inch Hitch
- 2000 lbs GTW
- CURT
more information >
Continue Researching
- Search Results: trailer hitch ball mount
- Search Results: brake controller
- Video: What to Know About the Curt TriFlex NEXT Trailer Brake Controller
- Video: Review of Caliber Boat Trailer Parts - Marine Slides for Boat Trailer Bunks - CA26AJ
- Shop: Brake Controller
- Q&A: Troubleshooting Curt Triflex Brake Controller Showing OL Code on Display
- Q&A: Where is Brake Controller Install Connector in 2019 Honda Ridgeline
- Q&A: Highest Rise Ball Mount for a 1-1/4" Hitch
- Shop: Redarc Tow-Pro Liberty Brake Controller w/ Custom Harness - Dash Knob - Up to 2 Axles - Proportional
- Shop: Curt TriFlex NEXT Trailer Brake Controller w/ Custom Harness - 1 to 4 Axles - Proportional
- Shop: Caliber Marine Slides for Boat Trailer Bunks - 1-1/2" Wide - Black - Qty 10
- Shop: Curt RockerBall Shock Absorbing 2" Hitch Ball - 3/4" Diameter Shank - Chrome - 3.5K
- Shop: Curt Class I Drawbar - 5" Rise - 9-9/16" Long - 2,000 lbs
- Q&A: Can I Change My Trailer Coupler from a 1-7/8 Inch Coupler to a 2 Inch Coupler
- Q&A: Solution for 1-1/4" Ball Mount With 7" Rise for 2016 Honda CRV-EX Towing U-Haul Trailer
- Shop: Curt Class II Drawbar - 3/4" Rise, 1-1/4" Drop - 6-3/4" Long - 3,500 lbs
- Shop: Curt RockerBall Shock Absorbing 2-5/16" Hitch Ball - 1" Diameter Shank - Chrome - 7.5K
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Video: How to Choose a Trailer Brake Controller
- Article: Trailer Wiring Diagrams
- Search Results: trailer hitch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Trailer Wiring
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Search Results: trailer tires and wheels
- Article: How to Measure for Trailer Hitch Drop
- Search Results: trailer wiring
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Video: Redarc Tow-Pro Liberty Brake Controller Review RED24FR
- Search Results: trailer jack
on Trailer Hitch Ball Mount
Jerred H.
9/29/2025
Hey Larry, did the combination of the Curt Class I Drawbar and the Curt RockerBall work out for your friend's trailer? I'm curious to know if it provided the right height for towing, as it could help others with similar needs.