How Long is the Replacement Hall Effect Sensor Wire Harness for Lippert Ground Control 3.0 LC65ED?

Question

Question:

What is the length of this harness?

asked by: Derek

0

Expert Reply:

Hey Derek! I just heard back from Lippert and the Replacement Hall Effect Sensor Wire Harness for Lippert Ground Control 3.0 - Rear Driver's Side item # LC65ED measures 424" long. If you add in the breakout tails it adds right at 11" to the total length.

If you have any additional questions go ahead and throw them into the comment box below and I'll be happy to help you.

expert reply by: Jerred H

0

Jerred H.

9/26/2025

Hey Derek, did the length of the harness work out for your needs? If you’re still looking for a solution, I’m happy to help.

Answer 1

We definitely have options for that, Joe! The Lippert Ground Control 3.0 you asked this question from is actually what I would recommend. If is featured in a bunch of OEM set ups and is by far the best one on the market. It can handle campers with a…

view full answer...

Answer 2

The correct replacement leg will depend on your retracted height as well as the side the leg is on. We have the following available: -Replacement 24-1/2" Right Rear Leg #LC344792 -Replacement 22-1/2" Right Rear Leg #LC428493 -Replacement…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

How Long is the Replacement Hall Effect Sensor Wire Harness for Lippert Ground Control 3.0 LC65ED?

Product Page this Question was Asked From

Continue Researching