Are the Galvanized Easy Grease Trailer Hub/Drum Assembly for 3.5K Axles Hot Dipped or Sprayed?

Question

Question:

Are these drum assemblies hot dipped galvanized or just spray on galvanization?

asked by: Shane

0

Expert Reply:

The Easy Grease Trailer Hub/Drum Assembly for 3.5K Axles item # AKHD-545-35-G-EZ-K are hot dipped to get the galvanized finish. These hubs have a 5 on 4-1/2 and fit 3,500 lbs Dexter axles with #84 spindles.

What kind of trailer are you looking to install them on?

expert reply by: Jerred H

0

Shane

4/13/2025

I’m putting them on a load rite 5 star single axle boat trailer. The axle is made by Knott and is a torsion style with standard size bearings.

Jerred H.

4/14/2025

@Shane That's cool! The item # AKHD-545-35-G-EZ-K hub is going to fit item # L68149 inner bearings and item # L44649 outer bearings. Let me know if you need any additional help!

Answer 1

Hey Steve, thanks for reaching out. So all of the 3,500 lb brake assemblies we offer use a standard 4-bolt mounting flange. The center on center horizontal measurement of the mounting bolts are 2-7/8 inches and diagonal center on center of 4 inches.…

view full answer...

Answer 2

Hey Anthony, yes, the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers - 55 Amp, #PD4655V is what you are looking for. This upgrades or replaces the converter section for 55-amp Parallax/Magnetek, WFCO, or Parallax RV power…

view full answer...

Answer 3

Yes, the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers - 55 Amp item #PD4655V is the correct replacement for the converter section of the Parallax model 7155. I have linked the installation instructions and a review video.

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 8

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 9

The Dexter Nev-R-Adjust electric trailer brakes can be manually adjusted. There are a couple teeth of the adjustment wheel that are exposed just under the lever that you referenced. I have attached a photo showing the teeth. You will likely need a…

view full answer...

Answer 10

I currently have four different self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes. You can choose from the following: -Terran Axle Electric Trailer Brakes #TX97ZJ (3,500 Axles) -etrailer Electric Trailer…

view full answer...

Answer 11

Hi Rusty; the Dexter #84546UC3-EZ and etrailer #AKHD-5475-35-K will both fit a 3,500 lb axle but they have different bolt patterns. You already ordered the Dexter in the past so I'm assuming your wheels are 5 on 4-1/2. For the same bolt pattern…

view full answer...

Are the Galvanized Easy Grease Trailer Hub/Drum Assembly for 3.5K Axles Hot Dipped or Sprayed?

Product Page this Question was Asked From

Continue Researching