Do you Have to Use the AcmeClamp Installation Tool for SuperSprings Installation?

Question

Question:

I purchased the SSA25 kit for the rear of my 2016 f250 4x4. Will the SS62EV installation tool be needed?

asked by: Charles

0

Expert Reply:

Hello Charles,

Great question. You don't HAVE to use the AcmeClamp Installation Tool for SuperSprings - Medium/Heavy Duty # SS62EV, you can use a different high capacity clamp if you have one. Using the # SS62EV would be ideal for the most simple and safest installation. I included the part of the instructions where it goes over the clamps, I highlighted the part as well.

Please let me know how the installation goes and how you like it after you give it a test drive.

expert reply by: Kate F

0

SuperSprings Custom Suspension Stabilizer instructions where it talks about the clamps.
(click to enlarge)

Kate F.

10/30/2025

Hey Charles, how did the install of the SuperSprings kit on your F-250 turn out? Did the AcmeClamp tool make things easier during the process? Your feedback could really help others setting up the same kit.

Answer 1

This is a great question and if you speak with Supersprings they'll tell you that actually running both is their preferred option to get the best of both worlds. The SuperSprings part #SSA47 that fit your RV will give you the additional load…

view full answer...

Answer 2

I attached a picture that shows how the PSP7 plate of the #SSA25 is installed on your 2017 Ford F-350. Both sets of the plates would not be needed.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 6

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

Hello Joe, Thank you for reaching out! The Power Mountain Tallboy Off-Road Bottle Jack - 11-5/16" to 27-1/16" Lift - 12 Tons #PM94FR does have the capacity you’d need, but since your fifth wheel’s frame sits about 25" off the ground,…

view full answer...

Answer 9

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 10

Hey Cory, Air springs are going to be the best at leveling your F-350 back out once the weight is added but they will most likely affect your unloaded ride quality, even when aired down. That being said, a majority of the unloaded ride quality…

view full answer...

Answer 11

Hi George, That’s a great question. The SmartPlug RV power inlet kits only come with straight connectors there isn’t a 90 degree connector sold separately by itself. The only 50 amp 90 degree angled cord SmartPlug currently offers is part #SM54SB. If…

view full answer...

Answer 12

Hey Jeff, I would strongly recommend the SumoSpring kit part #SS96EV for your 2025 Nissan Frontier. This will give you the support you are looking for without causing the ride quality to be overly harsh which the Timbrens are known to do. Install is…

view full answer...

Do you Have to Use the AcmeClamp Installation Tool for SuperSprings Installation?

Product Page this Question was Asked From

Continue Researching