Can Lippert Electric Tread Lite Steps Be Added to 2023 Forest River Sunseeker 3250

Question

Question:

i own a forest river sunseeker 3250 which dont have power steps, i want to knw if i can install the electric lippert two steps to it. Thank You Robert

asked by: Roberto H

0

Expert Reply:

Hello again Robert; you can definitely add those steps to your 2023 Forest River Sunseeker 3250. To find the correct steps you need to measure. Assuming the entry height is 19-1/2"-22-1/2" then the 2 step version is correct.

The Tread Lite electric steps attach to the underside of the camper chassis, directly beneath the doorway where your current steps are located. In addition to the entry height, measure the width and depth of the available space to make sure the steps will fit.

The # LC353543 which are 23-3/4" wide require a mounting space that is at least 25-5/8" wide and 18" deep. The 30" version # LC353621 requires the space to be at least at least 32" wide and 18" deep. Mounting hardware is sold separately # LC118155-72.

Since you don't have powered steps now you will also have to run wire to power the steps. Here is the complete installation process:

1. Hook up the steps to power to verify that all components are in working order
2. Make sure the camper is level on flat ground
3. Lift the steps into the mounting space and prop into place
4. If needed, mark the mounting holes on the camper and drill
-Set aside steps before drilling

5. If needed, install the outriggers
6. Align step mounting holes and secure in place with carriage bots and flange lock nuts
-Make sure bracket is backed up fully against the I-beam on the chassis

-Hardware not included

7. Tighten hardware until snug
8. Make sure assembly is sitting square and level
9. Torque the hardware tight
10. Connect the appropriate writing to your vehicle's source

expert reply by: Robin H

0

Entry Height
(click to enlarge)

Roberto H.

2/3/2025

My forest river sunseeker 32050 doesnt come with no step at all,can I still use this one, you are talking about,also do you have any wire diagram of the connection,Thank you so much Budd for your help. Best Robert

Robin H.

2/3/2025

@RobertoH if you take a look at the product page for either one you will see in the pictures it was installed with a cutout for a step and without so either way you can make it work. Here is a link to the wiring diagram https://support.lci1.com/documents/tread-lite-wiring-diagram

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 6

Hey Donny! For your Dometic Penguin/Brisk Air 15,000 BTU AC model B59516.711C0-MX, the correct soft start is the #DMC93JF. This is designed for Dometic Brisk II electronic air conditioner units with in-wall thermostats.

view full answer...

Answer 7

That’s a great question Chadwick, and this is one of those situations where the change in technology really matters. The GE Appliances Low-Profile RV AC w/ Heat Pump part #GE26RR will replace your current ARC13AACBL2 setup, but it’s important to know…

view full answer...

Answer 8

Hey Steven, thanks for all of the info you listed on your Grand Design 310GK! Based on that the correct Lippert SolidStep RV Steps are the #LC791574 that you referenced. This matches your doorway width and is a 4 step like you have as well. Is your…

view full answer...

Answer 9

Hey Bob, thanks for reaching out. The standard PD9160A was designed around lead-acid charging profiles, so that won't provide a proper charge to your lithium batteries. The best move will be to upgrade to the Progressive Dynamics 9300 Series RV…

view full answer...

Answer 10

Hi Jeff, Nice choice with the 100 amp hour Go Power Lithium RV Battery #GP99QR as well as the Expansion Kit #34282182. Also, you can absolutely replace your PD9260 with the PD9360 model that is compatible with lithium batteries, and our part number…

view full answer...

Answer 11

Hello again Robert; you can definitely add those steps to your 2023 Forest River Sunseeker 3250. To find the correct steps you need to measure. Assuming the entry height is 19-1/2"-22-1/2" then the 2 step version is correct. The Tread Lite…

view full answer...

Can Lippert Electric Tread Lite Steps Be Added to 2023 Forest River Sunseeker 3250

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching