Solution for Flat Tow Braking System that Goes from Air Force One to RV with Hydraulic Brakes

Question

Question:

I have a tow vehicle that is set up for Air Force One. I changed rvs. I now have a super c rv that does not have compressed air. Could you tell me what I would need to do to get my RV able to connect up to Air Force One?

asked by: Louis I

0

Expert Reply:

Hey Louis, we actually have a kit designed for your exact situation with the Towed Car Conversion Kit - Demco Air Force One to Stay-IN-Play Duo Flat Tow Brake System # SM99231. This will convert what is left of your Air Force One setup to be a Stay In Play for hydraulic brakes so that you can operate the brakes with your current RV. Are you familiar with the Stay In Play?

expert reply by: Jameson C

0

Jameson C.

11/3/2025

Hey Louis, how did things go with the Stay-IN-Play conversion kit for your new Super C RV? Your results could really help others switching from an Air Force One setup to a hydraulic brake system.

Louis I.

11/3/2025

@JamesonC I was getting information for my brother super c and he decided not to put it on. Sorry

Answer 1

I'm going to recommend installing the Demco Stay-IN-Play DUO Supplemental Braking System #DM86VR on your 2008 Jeep Wrangler. You will be able to reuse some of the wiring like the breakaway switch and air lines that tie into the vacuum brake…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 10

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Solution for Flat Tow Braking System that Goes from Air Force One to RV with Hydraulic Brakes

Product Page this Question was Asked From

Continue Researching