Availability of Top Cap of Ram 12k Trailer Jack

Question

Question:

Would you have caps for RAM 12k leg jack?

asked by: Cayley

0

Expert Reply:

Hey Cayley, yes we do have the cap you are looking for with the part # TJD-12000-CP.

expert reply by: Jameson C

0

Cayley

1/3/2025

A live chat agent was able to find it for me. Part number, TJD-12000-CP

Jameson C.

1/3/2025

@Cayley Sorry about that! The title saying it fit 10k jacks messed me up.

Answer 1

As long as all the other voltage and information matches you are able to use the CBB65-R Capacitor #FR65FR in place of your C65-R. These are simply series information numbers which I have found both listed on the exact same capacitor.

view full answer...

Answer 2

Hey Bryan, Dometic has the CT Thermostat and Control Board part #DMC83ZR as a fit for all single zone Dometic units so yes it would work well on your Duo Therm.

view full answer...

Answer 3

We do offer both round and square replacement caps for many brands of jacks. All are shown on the linked page. Part #TJD-12000-CP fits a 4 x 4-inch outer jack tube like on #TJD-12000SP-F2.

view full answer...

Answer 4

The Kenda Karrier 235/80-16 wheel/tire combo you specified, part #AM32743B would have a zero offset, like most trailer wheels do. The only wheel/tire combo we offer in the 235/80-16 tire size on a dual wheel we offer is part #TA45FR from Taskmaster.…

view full answer...

Answer 5

The only reason that I can see that those tabs would have been welded onto your frame is to restrict articulation of the equalizer. And the only reason I would see anyone putting those on is if the articulation was causing the tires to contact the…

view full answer...

Answer 6

The Equalizer from the Tandem-Axle Trailer Equalizer Kit for 2" Slipper Springs #AP216 is available without the hardware. The Equalizer for 2" Wide Slipper Springs #TREQ1344 is what you are looking for.

view full answer...

Answer 7

Hi Ryan, Really appreciate that detailed info, and we can get you the equalizer you're looking for, as well as the bolt. The parts you're looking for are the following: - Equalizer for 2" Wide Slipper Springs - 11" Long - 7/8"…

view full answer...

Answer 8

The equalizer in the Tandem-Axle Trailer Equalizer Kit #AP216 is 11-1/2" on center from the outer spring mounting holes when measuring horizontal separation. One hole will be 6" on center from the equalizer mounting hole center and the…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Availability of Top Cap of Ram 12k Trailer Jack

Product Page this Question was Asked From

Continue Researching