What Axle Seal Does the LC160 Axle 6k Use

Question

Question:

What axle seal does the LC160 axle take??

asked by: Eric

0

Expert Reply:

Hey Eric, the Lippert 6k axle you have would use the axle seal pair part # RG06-070 which has an inner diameter of 2.25 inch and an outer diameter of 3.376 inch.

expert reply by: Jameson C

0

Jameson C.

12/15/2025

Hey Eric, how did the axle seals work out on your Lippert 6k axle? Knowing how the fit turned out could help others trying to match the same setup.

Answer 1

Hey George, honestly not much really. The Timken brand like the seal part #TMK98ZR used to be associated with being made in the USA and higher quality but they aren't made in USA any longer so between that and the part #RG06-070 there's not…

view full answer...

Answer 2

Thanks for the pictures! Based on the weight of your 2008 Keystone Cougar 5th Wheel, you will want the item #LG-1 landing gear set. You are going to want to measure to be sure this is the right size for you. The two things you will want to measure…

view full answer...

Answer 3

In order to pick out replacement leaf springs for your trailer you will need to determine the axle's weight capacity and measure the length and width of your existing leaf spring stack. If the main info tag/plate is missing from the trailer and…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

What Axle Seal Does the LC160 Axle 6k Use

Product Page this Question was Asked From

Continue Researching