What is Difference Between TruRyde and Timken Grease Seals

Question

Question:

What is the difference between Timkon and truryde seal 010-036-00

asked by: George K

0

Expert Reply:

Hey George, honestly not much really. The Timken brand like the seal part # TMK98ZR used to be associated with being made in the USA and higher quality but they aren't made in USA any longer so between that and the part # RG06-070 there's not much of a difference.

expert reply by: Jameson C

0

George K.

7/22/2024

Thanks!

Jameson C.

7/22/2024

@GeorgeK No prob!

Answer 1

Hey Robert, welcome back! The Dexter 010-036-00, our item #RG06-070, and the Timken item #TMK58ZR are functionally the same grease seal. Timken is known for using higher quality materials in their parts so they do cost noticeably more. Both the item…

view full answer...

Answer 2

Hi Roger! I contacted Dexter with your axle information and you will need the #25580 inner bearing and #14125A outer bearing. If you want the races as well, you will need the #25520 and #14276 respectively. The seal will be the Double Lip -…

view full answer...

Answer 3

Dexter brake assemblies like the part #23-458-459 are essentially the best ones on the market. They use the best materials and and incredibly reliable and well-made. That being said the etrailer.com brand assemblies part #AKEBRK-7-SA are also very…

view full answer...

Answer 4

Hello Brandon. Thank you for all the axle information. I sent the information off to Dexter and they were able to supply me with a read out of your axle so I can get the spindle information. You need the Grease Seals 10-36 (pair) #RG06-070 it has a…

view full answer...

Answer 5

If the surface on the inside of the drum where the shoe pads make contact isn't smooth then a brake shop may be able to turn the drums. If that surface or the surface where the magnet makes contact (called the armature surface) is discolored then…

view full answer...

Answer 6

Hello Nick. The #TMK98ZR seal is made by Timken. It has a 2.250" ID and 3.376" OD .This is one in the same as the National 452920/482920 seal so they are interchangeable. A lot of folks prefer the Timken brand since they are made here in…

view full answer...

Answer 7

Hey Jason, thanks for reaching out! We have the Bearing Kit #BK3-100 which comes with everything you're needing, but these are made overseas. In order to get a set of Timken you'll need to order the following: - 25580 #TMK44FR - 25520…

view full answer...

Answer 8

Yes, going from a 4 leaf to a 6 leaf spring would add slightly to your ride height. For example, if the current 4 leaf spring has 3/8" thick leaves, and you go to a 6 leaf spring with 3/8" thick leaves, you would be adding 3/4" of…

view full answer...

Answer 9

The Tekonsha Prodigy RF Wireless Trailer Brake Controller doesn't tell us the color coding but does show the corresponding function locations. Based on this, you will use the Bargman 7-Way, RV-Style Connector w/ 6' Heavy Duty Insulated Cable…

view full answer...

Answer 10

You will want to measure your spindle to make sure (see accompanying photo) but the double lip grease seal that fits Dexter axles that are rated for 5,200 lbs - 7,000 lbs is #GS-2125DL. If you look at the photo you will want to use a digital caliper…

view full answer...

Answer 11

The Lippert 5,200lb axle under your 2015 Open Range Light 311FLR 5TH Wheel is going to need 2 Seals #GS-2250DL per axle. We do have the Bearing Kit #BK3-300 which will contain the races, bearings, a seal and cotter pin for one hub. This would be good…

view full answer...

Answer 12

Marc, it is suggested that you go up to 6k springs using the 6-Leaf Double-Eye Spring for 6,000-lb Trailer Axles #e94SR. These springs have the same 26" measurement, have 1 3/4" wide leaves, and a 3k spring capacity.

view full answer...

What is Difference Between TruRyde and Timken Grease Seals

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching