Can The Cover Plate Of The Lippert Smart Jack # LC643589 Be Replaced

Question

Question:

Can I buy that plastic cover plate everything works but its weathered off I just need the plastic cover

asked by: JosephASottileJr

0

Expert Reply:

Hey Joseph,

Lippert unfortunately offers zero replacement parts for the Lippert Smart Jack Electric Trailer Jack w/ Footplate # LC643589 so you can only replace the jack as a whole. I recommend using a cover # UF38-944020 to help shield your jack head from the elements and any further weathering.

expert reply by: Kevin C

0

Answer 1

Unfortunately, Lippert doesn't offer replacement parts for the Lippert Smart Jack Electric Trailer Jack w/ Footplate #LC643589 so the only way to get them would be to take them off of another Lippert Smart Jack. I highly recommend swapping out…

view full answer...

Answer 2

The only way to get a new control panel would be to replace your entire Smart Jack with part #LC643589. I reached out to my contact at Lippert who confirmed that the only replacement parts for the jack includes hardware like the pin or the footplate.…

view full answer...

Answer 3

Yes, the Ventline Pinnacle Ducted RV Range Hood with Light #VE98SR can replace your existing High Pointe range hood. This has the same dimensions at 20" wide x 18" deep x 4-3/4" tall. There will be a small difference in the vent…

view full answer...

Answer 4

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Hi Eric, Thanks for your question. As long as you are able to remove the factory hitch from your 2025 GMC Sierra 2500, the #C96CR will work as a replacement. Of note, the #C96CR will more than likely mount up a bit differently than your factory…

view full answer...

Answer 9

Hi Dennis! The Hellwig Load Pro 35 Heavy Duty Helper Springs with Custom Mounting Kit - Above Axle #HE93XR can potentially raise an unloaded truck a little, but it's going to be very minimal and will really only happen if your suspension is…

view full answer...

Answer 10

Hey Aaron, thanks for reaching out. Based on the specs I found online, the Americana Modular Wheel #AM92NR shares the same dimensions as your SRW 31767A9 trailer wheel. It has the same 17.5" x 6.75" size with 8 on 6.5" bolt pattern and…

view full answer...

Answer 11

Hey Carter, thanks for reaching out! The GM trucks with the 6-1/2' bed can use a stationary hitch as long as the 5th wheel trailer has a tapered nose. For your 2025 GMC Sierra 2500 I recommend using the PullRite OEX SuperLite #PUL96ZR for a few…

view full answer...

Answer 12

Hey Matt, while we haven't had the chance to get a picture of the Curt hitch part #C96CR installed we have had chance with the 2 inch version of the hitch part #C35CR which I attached below. It's on a truck with a service body though so that…

view full answer...

Can The Cover Plate Of The Lippert Smart Jack # LC643589 Be Replaced

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching