Capacity Of The Replacement Gas Strut for Roadmaster Tow Defender # RM-200023-50

Question

Question:

Code: RM-200023-50. what is the pressure of this shock 10 pounds ? you list other one that are less in cost

asked by: Mark

0

Expert Reply:

Hey Mark,

The Replacement Gas Strut for Roadmaster Tow Defender # RM-200023-50 is a 65lb gas strut.

expert reply by: Kevin C

0

Jerred H.

12/22/2025

Hey Mark, did the 65‑lb gas strut end up working for your Tow Defender? Knowing how it performed could help others looking for the right replacement.

Answer 1

In order to replace the Replacement Gas Struts part #RM-200023-50 on your Roadmaster Tow Defender Protective Screening part #RM-4750 you will first need to obtain a pick tool or a simple flathead screwdriver will suffice. Once you have this you will…

view full answer...

Answer 2

The Replacement 20-1/2" Gas Strut for Roadmaster Tow Defender Protective Screening #RM-200023-50 is the part you are seeking for your #RM-4750.

view full answer...

Answer 3

Hey Cole! The Replacement Collar Attachment Hardware Kit #RM-4800-30 is only really needed if your old hardware is worn out, so you'd be the best person to determine that, actually. Just look for any places where it might be damaged, rusted, or…

view full answer...

Answer 4

I checked with Roadmaster and the part #RM-200023-50 will fit your Defender part 4700 as long as the strut you have is 20-1/2 inches.

view full answer...

Answer 5

Sounds like you have the Roadmaster Tow Defender #RM-4750 which means for a replacement screen you'd need the #RM-4750-10. Then for the replacement shock you'd need the part #RM-200023-50 and you'd be set.

view full answer...

Answer 6

The distance from the top of the mounting plate to the bottom of the wheel on the Ultra-Fab 4 Inch Skid Wheels, #UF48-979011, is 5-3/4 inches and for the 6 Inch wheels, #UF48-979013, 7-3/4 inches. I have attached a photo for you showing these…

view full answer...

Answer 7

Carol, The Replacement Gas Strut for Roadmaster Tow Defender #RM-200023-50 only has a 65 lb rating so you'll need something closer to that 110 lb rating like one of the following: - Universal Gas Strut - 107 to 117 lbs Force - 19-11/16"…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Capacity Of The Replacement Gas Strut for Roadmaster Tow Defender # RM-200023-50

Product Page this Question was Asked From

Continue Researching