PVC Grommet Thickness for the Optronics Fleet LED Trailer Tail Lights

Question

Question:

What is the maximum thickness the metal can be to accept the rubber grommet?

asked by: Nick

0

Expert Reply:

Nick, the PVC Grommet # a70gb is 1 1/8" thick so you could use up to an 1 1/8" thick metal.

expert reply by: Bryce D

0

PVC Grommet Dimensions
(click to enlarge)

Jerred H.

12/22/2025

Hey Nick, did the 1 1/8-inch thickness on the PVC grommet work well with your trailer tail lights? Knowing how it fit could help others trying to match the same setup.

Answer 1

Tire size 4.80-12 is not found on vehicles, but is a common trailer tire size on smaller utility- and sport-type trailers. In trailer use you do want to inflate them to the maximum cold psi pressure noted on the tire sidewall. Trailer tires should…

view full answer...

Answer 2

Hey Bob, yes we do have a rubber grommet that you can use with the Optronics trailer light part #ST70RB with the part #a70gb.

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 6

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

PVC Grommet Thickness for the Optronics Fleet LED Trailer Tail Lights

Product Page this Question was Asked From

Continue Researching