Replacement Filler Cap for Dexter DX7.5 Brake Actuator

Question

Question:

I need a filler cap, with the , for a Dexter DX 7.5 actuator. Do you have any idea where I might find one? I have done a pretty complete search of the internet with no success. Maybe I am just not recognizing one.

asked by: Dick W

0

Expert Reply:

Hello Dick; the correct replacement cap for a Dexter DX7.5L A-60 like # DX56FR is the # T097-022-00. I went ahead and attached a picture with the dimensions below if you want to compare it to your actuator.

expert reply by: Robin H

0

T097-022-00 Dimensions
(click to enlarge)

Dick W.

9/24/2024

Thank you

Answer 1

Hey Mike, yes the replacement cap part #T097-022-00 that you referenced is the correct replacement cap for a Dexter Model A-60/A-75 brake actuator like it sounds like you have.

view full answer...

Answer 2

I have a couple of good options for you but there aren't any available adapters. Instead you will remove your current pigtails like the Optronics 2-Wire Marker Light Pigtails part #AL42PB. Once removed you add the the 2-Wire Pigtail for Optronics…

view full answer...

Answer 3

The correct replacement cap for your Dexter DX7.5L A-60 #DX89FR is the #T097-022-00.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Replacement Filler Cap for Dexter DX7.5 Brake Actuator

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching